(m)
REMOVE ARMREST FOAM ASSEMBLY (Ref Fig 3001 sheet 5/6) 1 Remove arm assembly. (Ref Step (l)) 2 Peel away aft beam covver to access fasteners. 3 Remove 2 schrews to remove aft end cap. 4 Slide armrest foam assembly aft to remove.
(n)
REMOVE LATCH LEVER (ARM ASSEMBLY) (Ref Fig 3001 sheet 5) 1 Simultaneously insert a samll wire or drill bit 8paper clip may be used into holes in the
upper latch housing to disengage latch lever. 2 Pull latch leer forward and twisting lever, as neeassary, to remove.
(o)
REMOVE LATCH (ARM ASSEMBLY) (Ref Fig 3001 sheet 5) 1 Remove arm assembly. (Ref Step (l)) 2 Remove latch lever (Ref Step (n)) 3 Remove 2 screws attaching upper latch housing. 4 Slide upper latch housing forward to remove. 5 Remove 1 screw from the cable assembly/adapter bracket. 6 Remove 2 forward deco extrusions to expose fasteners. 7
Remove 2 upper screws and 2 washers to unfasten adapter bracket. 8
Swivel upper cable assembly. 9
Pull adapter bracket up to remove 10 Remove 4 lewer screws and 4 washers to unfasten forward armrest beam.
Recaro Aircraft Seating GmbH & Co. KG, Daimlerstrasse 21, D.74523 Schw.bisch Hall
COMPONENT MAINTENANCE MANUAL . 6510A TYPE
654 SERIES
11 Slide armrest beam away from armrest panel assembly.
12 Remove remaining latch assembly components.
(p) REMOVE MAINTENACE COVER / KINEMATIC COVER . TYPICAL (Ref Fig 3001 sheet 1/7) 1 Remove 4 screws and 4 washers from under the seat to remove maintenance cover /
kinematic cover.
2 Peel maintenace cover / kinematic cover aft to disengage hook and loop tape from seat frame.
(q)
REMOVE MAINTENACE COVER / KINEMATIC COVER . LAST ROW (Ref Fig 3001 sheet 1 /7) 1 Peel S.cover up and aft to disengage hook and loop tape and to reveal fasteners. 2 Remove 4 screws and 4 washers remove maintenance cover / kinematic cover.
3 Peel maintenance cover / kinematic cover forward and up to disengage hook and loop tape.
(r)
REMOVE LITERATURE POCKET STRUCTURAL ASSEMBLY (Ref Fig 3001 sheet 1) 4 Remove deco literature closeout panel and S.shape panel (Ref Step (b)). 5 Remove literature door. (Ref Step (j)) 6 Remove maintenance cover / kinematic cover (Ref Step (p)). 7 Remove 4 screws from the literature pocket hinge bracket. 8 Slider literature pocket aft to remove
(s)
REMOVE REAR BUMPER ASSEMBLY (Ref Fig 3001 sheet 2) 1 Remove inboard an doutboard end bay deco panel. (Ref Step (c)) 2 Remove screws from outboard side of rear bumper assembly. 3 Gently pry the inboard flange away from literature pocket structural assembly. 4
(t)
REMOVE END CAP TRIM ASSEMBLY (Ref Fig 3001 sheet 2)
Remove Lieterature pocket structural assembly, if necessary.
5
Pull rear bumper assembly aft and down to remove.
Recaro Aircraft Seating GmbH & Co. KG, Daimlerstrasse 21, D.74523 Schw.bisch Hall 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：COMPONENT MAINTENANCE MANUAL WITH ILLUSTRATED PARTS LIST B757−200 PASSENGER SEAT 乘客座椅(33)
