曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

2
T
(Automatic Selection)
The SPEED SET page is used to configure the takeoff
speed page and provides TAKEOFF prompts
on the ACTIVE FLT PLAN page. All speed bugs disappears when airplane speed exceeds entered
VT speed by 10 knots and the airplane is at or above 1500 feet AGL. VR is positioned out further on
the outside of the speed tape, to allow V1 and VR to be displayed side by side should V1 be equal to
VR.
TAKEOFF 3/3
CLEAR CLIMB
V1
V2
VFTO
VR
1 Press PERF button and select TAKEOFF from PERF INDEX 1/2 .
PERF
2 Enter the desired speeds via line select key and alpha numeric key pad.
CLIMB
PERF INDEX
PERF INIT
1/2
PERF DATA
PERF PLAN TAKEOFF
CLIMB CRUISE
DESCENT LANDING
TAKEOFF 3/3
CLEAR CLIMB
V1
V2
117
108
VR
108
VFTO
172
TAKEOFF 3/3
CLEAR
V1
V2
VFTO
VR
GF1110_018
LANDING V SPEED
Landing V speed is selected through the FMS, automatically (magenta) or manually (cyan). The
SPEED SET page is used to configure the landing speed page and provides LANDING prompts on
the ACTIVE FLT PLAN page. Landing speeds can be entered at any time and are cancelled upon
landing.
1 Press PERF button and select LANDING from PERF INDEX 1/2.
LANDING 3/3
CLEAR FLT PLAN
PERF INDEX
PERF INIT
1/2
PERF DATA
PERF PLAN TAKEOFF
CLIMB CRUISE
DESCENT LANDING
VREF
GF1110_019
FLIGHT INSTRUMENTS
Flight Crew Operating Manual REV 46, Jul 21, 2005
CSP 700−6
Volume 2
11−10−16
LANDING V SPEED (CONT'D)
Landing Vspeed Bug
2 Enter the desired speed via line select key and alpha numeric key pad.
LANDING 3/3
CLEAR FLT PLAN
VREF
137
Automatic selection
Manual selection
Landing Vspeed Bug
GF1110_020
190
170
160
150
140
130
120
190
180
RF
155
6
4
RF
RF
FLAP/SLAT/GEAR EXTENSION SPEED BUGS
The flap/slat/gear extension speed bugs will appear anytime the airplane is 18,000 feet and below or
anytime that the landing gear is in operation, the flaps are selected out of 0 degrees and/or slats are
out.
GF1110_021a
SO − Slats Extended / Flaps 0° − 225 knots.
F − Flaps Extended 6°/16° − 210 knots.
LO − Landing Gear in Operation − 200 knots.
F3 − Flaps Extended 30° − 185 knots.
240
220
200
190
180
240
215
6
4
ALTITUDE TAPE
The altitude tape is capable of displaying altitudes between −980 and 65,000 feet (inclusive) and the
current barometric altitude ± 550 feet. The altitude tape is labeled at every 500 feet and has a
doublelined
chevron at each 1000 foot altitude and a singlelined
chevron at each 500 feet. A boxed
barberpole symbol will appear if the digital readout is < 10,000 feet. A minus sign will appear when a
negative altitude is displayed.
Negative Altitude
Altitude
Tape
500 feet
1000 feet
95 00
−200
Below 10,000 feet
GF1110_022
104 00
9500
10500
100 00
FLIGHT INSTRUMENTS
REV 46, Jul 21, 2005 Flight Crew Operating Manual
CSP 700−6
Volume 2
11−10−17
ALTITUDE TREND VECTOR
Altitude trend vector information is derived from the selected ADC. It will indicate what the altitude of
the airplane will be in 6 consecutive seconds, based on current vertical speed.
SELECTED ALTITUDE READOUT
The readout reflects the position of the altitude reference bug on both PFDs, with a range of 0 to
51,000 feet.
A boxed barberpole symbol will appear if the digital readout is < 10,000 feet.
The readout can be displayed in metric, with a range of 0 to 15,500 meters, using the MENU display
selection on the MFD control panel, located on the pedestal.
SELECTED ALTITUDE BUG
The altitude bug is set using the ALT knob on the guidance panel. The bug will park at the
appropriate end of the altitude tape when off scale. At this position, one half of the bug will be in view.
Selected
Altitude Bug
Altitude
Trend Vector
Altitude
Rolling Digits
Selected
Altitude Readout
Below 10,000 feet Guidance Panel
Selected Altitude Readout − Metric
MFD Menu
Guidance Panel
MFD Control Panel
GF1110_023
104 00
9500
10500
100 00
80 00
VERT PROFILE
METRIC ALT ON
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：龐巴迪挑戰者手冊6(151)