曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

five (5) seconds.
Check altitude modes and
commands.
ANTI-SKID FAIL
(Brake-By-Wire)
Normal anti-skid control
circuit or other failure:
system has switched to
open loop pulsed antiskid
control.
OR:
ANTI SKID switch
selected to OFF.
Verify ANTI SKID switch is ON.
If switch is ON, see Section
05-02-10, Anti-Skid Failure
(Brake-By-Wire).
OPERATING MANUAL
MESSAGES AND ANNUNCIATIONS PROCEDURES 04-03-00
Page 1
October 11/02
Revision 8
CAS Message: Possible Cause(s): Corrective Action:
ANTI-SKID FAIL
(HMAB)
Miscompare in 28V DC
power supplies or in
nutcracker switches.
OR:
ANTI SKID switch
selected to OFF or
system circuit problems.
OR:
Auxiliary hydraulic
system fails to energize
or pressure fails to rise
within three (3) seconds
after brake pedals are
depressed.
See Section 05-02-40, Anti-Skid
Failure (HMAB).
AOA HEAT 1-2 FAIL Angle of attack probe
heater failed.
Check circuit breakers (CBs):
• AOA PRB HTR #1: Copilot’s
Aft Panel, L-14
• AOA PRB HTR #2: Copilot’s
Aft Panel, M-14
If normal, avoid icing conditions
if possible. If flight into icing
conditions is unavoidable, pull
appropriate Stall Warning
Computer CB and monitor other
system:
• STALL WARN CMPTR #1:
Copilot’s Overhead, A-12
• STALL WARN CMPTR #2:
Copilot’s Overhead, B-12
Full stall barrier protection is
provided by the operative
system.
AP OFF Autopilot disconnected
by other than normal
means.
Press Autopilot Disconnect (AP
DISC) button to clear message,
or reengage autopilot.
AP TRIM FAIL Autotrim function of
AFGCS has failed.
Verify PITCH TRIM switch is
engaged (DISEN legend
extinguished).
If PITCH TRIM switch DISEN
legend is extinguished:
(1) Grasp yoke securely
(expect out of trim
condition).
(2) Disconnect autopilot.
(3) Retrim airplane.
(4) Attempt to determine
problem.
APU ALT BRG FAIL Alternator main bearing
has failed and is
operating on auxiliary
bearing.
Operation on auxiliary bearing
can continue for fifteen (15)
hours at full load or fifty (50)
hours at no load. Message will
remain displayed. Time of
occurrence should be recorded.
APU ALT HOT APU alternator
temperature above 300°
F (149° C).
Shut off APU alternator using
ELECTRIC MASTER, AUX
PWR switch.
OPERATING MANUAL
04-03-00 MESSAGES AND ANNUNCIATIONS PROCEDURES
Page 2
October 11/02
Revision 8
CAS Message: Possible Cause(s): Corrective Action:
APU LOAD
(SPZ-8400 Equipped
Airplanes)
APU electrical load for
operation above 30,000
ft not within limits.
Adjust electrical load up or
down as necessary.
APU MASTER WARN APU MASTER switch is
ON, but APU is not
running.
Select APU MASTER switch to
OFF or start APU.
AUX AC POWER FAIL Power output from APU
alternator has failed or
dropped off line.
Select ELECTRIC MASTER,
AUX PWR switch OFF, then
ON. If condition remains
unchanged, select ELECTRIC
MASTER, AUX PWR switch
OFF. If necessary, see Section
05-04-40, APU Alternator
Failure.
AUXILIARY HYD HOT Auxiliary hydraulic pump
case temperature above
300° F (149° C).
Select auxiliary hydraulic pump
OFF, if practicable.
BAGGAGE DOOR
(SN 1000-1389 having
ASC 415B; SN 1390 &
subs.)
Baggage door is open
or unlocked.
Close and lock baggage door
as required.
BATT 1-2 CHGR FAIL Battery or Battery
Charger has failed, or
input power CB is open.
(1) Check BATTERY
CHARGER CB(s) on PDB.
(a) If open, close CB.
(b) If CHGR FAIL remains
displayed, deactivate
battery charger by
pulling CB. CHGR
FAIL will remain
displayed.
(2) If CB is closed, battery or
battery charger has failed.
See Section 05-07-80,
Battery Or Battery Charger
Failure.
BATT ON BUS Essential DC Bus
powered by batteries
only.
See Section 05-07-90, Essential
DC ESS ON BATT DC Bus On Battery Power.
(Added by ASC 415 for
SPZ-8000 equipped
airplanes.)
L-R BLEED AIR HOT Bleed air temperature is
above 550° F (288° C).
(1) Select appropriate BLEED
AIR switch to OFF.
(2) When annunciation is
extinguished:
(a) Select ISOLATION
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：灣流4操作手冊 Gulfstream IV Operating Manual 3(51)