曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Approximately 60 seconds later, the maximum turn rate is
reduced to 15% standard rate.
4. For increased sensitivity during GPS approach or if desired for
enroute tracking, press the APR button on the autopilot
programmer/computer. The NAV, GPSS, and APR annunciators
will be illuminated. Use HDG to accomplish a procedure turn.
Engage GPSS again to complete the approach.
VOR Tracking and VOR-LOC Approach
1. Begin with a reliable VOR or VOR-LOC signal selected on the
NAV receiver.
2. Select desired course on HSI and establish a desired intercept
heading.
3. Press the NAV button on the autopilot programmer/computer. The
NAV mode will illuminate. Course interception and tracking will be
as described under GPS Tracking and GPS Approach above.
4. For station passage, set HDG bug to within 5° of selected course.
• Note •
If the HDG bug is within 5° of center and the course deviation
is less than 10%, the autopilot will immediately establish the
lowest level of sensitivity and limit the turn rate to a maximum
of 15% of a standard rate turn.
5. For increased sensitivity during approach or if desired for enroute
tracking, press the APR button on the autopilot programmer/
computer. Both NAV and APR annunciators will be illuminated.
Revision 4: 08-15-07
P/N 11934-S13 13 of 16
Cirrus Design Section 9
SR20 Supplements
Glideslope Intercept and Tracking
1. Begin with a reliable ILS signal selected on the NAV receiver.
2. Select autopilot NAV and APR. Airplane must be within 50%
needle deviation of localizer centerline.
3. Select ALT mode. Airplane must be 60% or more below the
glideslope centerline during the approach to the intercept point. If
the above conditions have existed for 10 seconds, GS mode will
arm, the GS annunciator will come on and the ALT annunciator will
remain illuminated. When glideslope intercept occurs, the ALT
annunciator will go out and the system will track the glideslope.
• Note •
If approach vectoring locates the airplane too near the
glideslope at the intercept point (usually the outer marker), the
GS mode can be manually armed by pressing the ALT button
once. Once capture is achieved, GS annunciator will come on
and ALT annunciator will go out.
Section 5 - Performance
There is no change to the airplane performance when the S-Tec
System 55X autopilot is installed.
Section 6 - Weight & Balance
There is no change to the airplane weight & balance when the S-Tec
System 55X autopilot is installed.
Section 7 - Systems Description
Autopilot
The airplane is equipped with an S-Tec System 55X two-axis
Automatic Flight Control System (Autopilot). The autopilot
programmer/computer is installed in the center console radio stack.
The autopilot roll axis uses an inclined gyro in the turn coordinator
case as the primary turn and roll rate sensor. In addition to the turn
coordinator instrument, the roll axis computer receives signals from
the HSI and the #1 NAV/GPS radio. The roll computer computes roll
steering commands for turns, radio intercepts, and tracking. Roll axis
Revision 4: 08-15-07
14 of 16 P/N 11934-S13
Section 9 Cirrus Design
Supplements SR20
steering is accomplished by autopilot steering commands to the
aileron trim motor and spring cartridge.
The pitch computer receives altitude data from the altitude encoder
pressure transducer plumbed into the static system, an accelerometer,
and glideslope information from the HSI and #1 NAV radio. Pitch axis
command for altitude hold, vertical speed hold, and glideslope tracking
is accomplished by pitch computer commands to the elevator trim
motor and trim cartridge.
28 VDC for autopilot and altitude selector/alerter is supplied through
the 5-amp AUTOPILOT circuit breaker on the MAIN BUS #1.
All Autopilot mode selection is performed by using the mode select
buttons and VS knob on the autopilot programmer/computer in the
center console. Annunciators in the programmer/computer display
window annunciate modes. Refer to Figure 1 for an illustration of the
programmer/computer.
RDY (Ready)– Illuminates when autopilot is ready for engagement.
When the airplane’s Battery Master switch is turned on and the rate
gyro RPM is correct, the RDY annunciator will come on indicating the
autopilot is ready for the functional check and operation. The autopilot
cannot be engaged unless the RDY light is illuminated.
HDG (Heading) Mode – When HDG is selected, the autopilot will
engage the HDG mode, fly the airplane to, and hold the heading set on
the HSI. Subsequent heading changes are made using the HDG knob
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Cirrus Design SR20西銳20飛行員操作手冊和飛機飛行手冊附錄(26)