曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

pressing the left key adjacent to desired mission. through 14.
Complete mission information will display. Initiating a
new mission request is accomplished by pressing a
NEW key of an available mission number on the Air 10. IDM switch  Press as required to display
Request list, selecting air mission type, entering the IDM Index page.
required parameters, receiving the summary, and
transmitting the data. 11. AIR REQ key  Press.
b. Types of air missions are as follows: 12. Desired mission (1-8) line number  Select.
(1) HELLFIRE wherein the number of rounds to
be fired is requested and guidance is by other than the 13. R-1 key  Press to display Air Mission
launching element. Summary page.
4-195
TM 1-1520-248-10
14. On Air Mission Summary page, SEND key 
Press.
NOTE
• Remote HELLFIRE (REMOTE HLFR)
mission request. The paging required for
a simplified request is depicted in fig. 4-
94.
• The Mission Status will change from
REQUESTED to ACCEPTED, READY,
FIRE, and SHOT. At completion of
mission an END OF MISSION message
should be sent.
• A generic Air Mission Summary page is
shown in fig. 4-95.
4-178. ARTILLERY REQUEST PAGES.
a. Description. The mission data contained in the
IDM is formatted to be consistent with the TACFIRE
Artillery Fire Direction Center (FDC) system and
associated forward observer digital message devices
(DMD). Artillery mission command selection is initially
entered on the ARTY Mission Summary page
automatically as REQ. Upon receipt of the TACFIRE
FDC message-to-observer (MTO), the mission
command will automatically change to FIRE. A READY
command will be displayed if the Battery Computer
System (BCS) is on-line with TACFIRE. Target position
(range and bearing from the helicopter) is automatically
calculated. By pressing the TGT PSN (target position)
key, the operator can manually enter the UTM grid,
range, bearing, and altitude of the target on subpages
if required.
The Artillery Request List stores two active artillery
missions and two preplanned mission requests on the
Preplanned Mission List subpage. Accessing either
active mission is accomplished by pressing the M1 or
M2 key on the ARTY REQ list page. To review a
preplanned mission, pressing the PPLN LIST key on
the Preplanned Mission List page will cause the
Preplanned Mission Summary page to display.
NOTE
In order to store a preplanned mission, a
preplan request must be executed and
stored as a standard artillery preplan
request. Then the mission must be inserted
into preplan list.
PULL
MAN
PULL
BKUP
BRT
C
ONT
VSD HSD MMS COMM
PULL
MAN
PULL
BKUP
BRT
C
ONT
HSD MMS COMM
PULL
MAN
PULL
BKUP
BRT
C
ONT
VSD HSD MMS COMM
RAPID
RAPID
IDM INDEX PAGE
AIR REQ
ARTY REQ
MOVEMENT
REPORTS
RCVD MSG
START
STATUS
MSGS/FTXT
AIR REQ LIST 1/3
1 N/G A/READY
2 ILLUM B/ACPTD
2 MLFR C/SHOT
/DELTD NEW
/DELTD NEW
/DELTD NEW
AIR MISSION REQUEST LIST PAGE 1-3
AIR MISSION TYPE SELECT PAGE
AIR MSN TYPE
HELLFIRE
RAPID
VSD
OTHER ORDNANCE
NO PREF
406530-47-2
J2997
I n i t i a t i n g a new a r t i l l e r y m i s s i o n r e q u e s t i s
Figure 4-94. Air Request Pages accomplished by pressing the NEW key of an available
4-196
TM 1-1520-248-10
mission number, selecting artillery mission type,
following prompts through the subpages, reviewing
Summary page, and transmitting data.
b. Types of artillery mission requests are as follows:
(1) NEW TGT wherein the observer defines
target type and strength.
(2) Known Point (KNPT TGT) wherein the
observer defines a point which is a location previously
identified and numbered, known both to the requestor
and to the artillery FDC. The requestor then provides
target type and strength.
(3) QUICK wherein the requestor enters only a
known point. All other data is known by the artillery
FDC.
(4) Preplanned (REQ PPLN) wherein the
observer provides type of fire request (either Final
Protective Fire (FPF) or Copperhead (CPHD) guided
munitions). Only one FPF can be preplanned at a time;
however, b o t h p r e p l a n n e d m i s s i o n s can be
Copperhead. The requestor then provides target
position and known point number.
(5) Copperhead (CPHD) wherein the target
position is defined as NEW or Known Point and point
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPTER 2(21)