曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

until all desired data has been sent.
(6) Select NEW TGT or KNPT TGT as
d. COMPLETE/R-4 key  Press to send desired.
COMPLETE message when finished with (7) ARTY Summary page appears... Press
bulk data transmission. SEND.
4-283
TM 1-1520-248-10
(8) Preplanned MTO from FDC accepts
PPLN request. NOTE
(9) Select IDM switch.
(10) Select ARTY REQ. A Copperhead is fired from an artillery 155
(11) Select PPLN LIST. MM gun.
(12) Press NEW P1 or P2 to designate the
desired preplanned mission number. 3. COPPERHEAD Fire Mission (Active and
(13) Press L-2 to insert PPLN request. Preplanned).
b. To enter a second preplanned request  a. Locate target using MMS.
repeat all of the previous steps listed in a.
above. b. Select IDM switch.
c. Select ARTY REQ.
2. NEW  ARTY FIRE MSN RQST.
d. Select NEW (Next to mission to be
a. Locate target using MMS for automatic entry replaced).
of coordinates.
e. Select CPHD.
b. Select IDM switch.
NOTE
c. Select ARTY REQ.
If KNPT TGT is selected, entry of two-digit
d. Select NEW (Next to mission to be KNPT number is required.
replaced).
f. Select NEW TGT or KNPT TGT as desired.
e. Mission Type  Select NEW TGT, KNPT
TGT, QUICK, REQ PPLN, or CPHD. g. S e l e c t S T R E N G T H i f n u m b e r o f
Copperheads to be fired is greater than one.
NOTE h. Review/Change Mission Summary page.
Fire control method will default to AMC FFE.
i. SEND key  Press.
f. Select fire control method. 4. To send a suppression mission (Quick).
g. TARGET TYPE  Select one of 15 targets. Selection of the QUICK Artillery Mission type follows
the same procedures as in step 3. above except a
KNPT or TGT number must be specified. After
NOTE specifying KNPT or TGT number, send Summary page.
Strength defaults to 1 ARMR.
4-235. AIR REQUEST (8 AERIAL FIRE
h. Select TARGET STRENGTH. MISSION REQUESTS ARE AVAILABLE).
i. R-1 key  Press. 1. Storing or executing a NEW Air Mission Fire
Request.
j. Select TGT RAD/LGTH, WIDTH, and
ATTITUDE. a. Locate target using MMS.
b. Select IDM switch.
k. R-1 key  Press.
c. Select AIR REQ.
l. Review/Change Mission Summary page. (1) AIR REQUEST List page  Select
Mission 1 through 8 from AIR REQ List
m. SEND key  Press. (pages 1-3) by pressing NEW.
4-284
TM 1-1520-248-10
(2) On MSN TYPE p a g e  S e l e c t g. SEND key  Press.
HELLFIRE, OTHER ORDNANCE, or NO
PREF. h. COMPLETE  SEND EOM message upon
(3) Make appropriate selections as needed. mission completion.
(4) Review/Change Mission Summary page.
NOTE
d. To execute an Immediate Fire Request,
Press SEND while on the Summary page. In a HELLFIRE mission, the Observer’s
(Mission will also be stored at this time.) M i s s i o n S t a t u s w i l l c h a n g e f r o m
REQUESTED to ACCEPTED to READY to
e. To enter other missions, proceed to step 1 FIRE to SHOT upon receipt of firing element
above. transmission.
2. Recalling a stored AIR MISSION:
4-236. RECEIVED MESSAGES.
a. Select IDM switch.
1. To Review a Received Message:
b. Select AIR REQ.
a. Select IDM switch.
c. Select desired mission number (1-8) from
pages 1, 2, or 3. b. Select RCVD MSG.
d. Review/Change Mission Summary page. c. To review a selected message  Press
appropriate key.
e. SEND key  Press.
d. I f a p p r o p r i a t e  DELETE r e v i e w e d
NOTE message to clear out Received Message
Buffer to make room for other incoming
HELLFIRE missiles are normally fired from messages.
aircraft.
2. NEW messages must be reviewed before
3. REMOTE HELLFIRE request. they can either be deleted or kept.
a. Select IDM switch. 3. Received Messages are indicated by the
advisory...IDM MESSAGE RECEIVED.
b. Select AIR REQ.
NOTE
c. Select NEW  On Air Mission Request List
page  Select 1 through 8. Selecting OTHER allows the entry of free
text messages.
d. Select HELLFIRE.
4-237. MOVEMENT.
e. Make appropriate selections as needed.
To Transmit Movement Messages:
NOTE
a. Select IDM switch.
• Number of rounds will default to one and b. Select MOVEMENT.
be displayed next to laser code.
• If more than one missile per code is c. Select Type of Movement.
needed, laser code must be input again
followed by number of missiles. d. S e l e c t D e s t i n a t i o n ( P R E S E T , MY
POSITION, OTHER). (Selecting OTHER
f. Review/Change Mission Summary page. allows the entry of free text messages).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPTER 2(53)