曝光臺(tái) 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費(fèi)者

e. Review/Change Summary page.
4-285
TM 1-1520-248-10
f. SEND key  Press. 4. To transmit CAS REPORT:
a. Select IDM switch.
4-238. REPORTS.
b. Select REPORTS.
1. To transmit own Situation/Status:
c. Select CAS.
a. Select IDM switch.
d. Manually enter CAS data to Summary page.
b. Select REPORTS.
e. Review/Change Summary page.
c. Select SIT/STATUS.
f. SEND key  Press.
d. Select activity to report.
5. To transmit ATI REPORT:
e. Review/Change Summary page.
a. Select IDM switch.
f. SEND key  Press.
b. Select REPORTS.
2. To transmit SPOT Report:
c. Select ATI.
a. Locate Target using MMS.
d. Select RELY Option.
b. Select IDM switch.
e. Select TARGET TYPE.
c. Select REPORTS.
f. Select TARGET STRENGTH.
d. Select SPOT.
g. Review/Change Summary page.
e. Select TARGET TYPE.
h. SEND key  Press.
f. Select TARGET STRENGTH.
6. To request a REPORT:
g. R-1 key  Press to select TARGET
ACTIVITY. a. Select IDM switch.
h. R-1 key  Press. b. Select REPORTS.
i. Review/Change Summary page. c. Select REQUEST.
j. SEND key  Press. d. Select REPORT TYPE (On report requests
Select page).
3. To transmit BDA Report:
e. Select DEST  (Enter Subscriber’s ID).
a. Select IDM switch.
f. Review/Change Summary page.
b. Select REPORTS.
g. SEND key  Press.
c. Select BDA.
d. Manually enter BDA data to Summary page. 4-239. STATUS.
e. Review/Change Summary page. 1. To review OWN STATUS:
f. SEND key  Press. a. Select IDM switch.
4-286
TM 1-1520-248-10
b. Select STATUS. 2. To review OTHER Subscribers Status:
c. Select OWN WPNS or OWN PPSN. a. Select IDM switch.
(1) F o r OWN WPNS  E n t e r L a s e r
Designator Code and Press R-1. b. Select STATUS.
(2) For OWN STATUS  Select ALT 
Enter Alt in Meters or N/G and Press R- c. Select SUB WPNS or SUB PSN. (Used for
1. specific subscribers).
d. Review OWN STATUS (selected through d. Review STATUS of selected subscribers.
Status Index page).
4-287/(4-288 blank)
TM 1-1520-248-10
CHAPTER 5
OPERATING LIMITS AND RESTRICTIONS
SECTION I. GENERAL
5-1. PURPOSE. 5-3. EXCEEDING OPERATIONAL LIMITS.
Anytime an operational l i m i t i s exceeded, an
This chapter identifies or refers to all important appropriate entry shall be made on DA Form 2408-13-1
operating limits and restrictions that shall be observed and 2408-13-1E. Entry shall state what limit or limits
during ground and flight operations. were exceeded and any additional data (i.e., range and
time beyond limits) that would aid maintenance
personnel in performing the required maintenance
action.
5-2. GENERAL.
The operating limitations set forth in this chapter are 5-4. MINIMUM CREW REQUIREMENTS.
the direct results of design analysis, test, and operating The minimum crew required to fly the helicopter is one
experiences. Compliance with these limits will allow the pilot whose station is in the right seat. An additional
pilot to safely perform the assigned missions and derive qualified crewmember is required when aircraft mission
maximum utility from the helicopter. equipment is employed.
SECTION II. SYSTEM LIMITS
5-5. INSTRUMENT MARKINGS (FIGURE 5-1). segment for NP, TRQ, and TGT will illuminate by
107%, 100%, and 802 °C. As input signals decrease,
a. Instrument Marking Codes. White wedge- light segments extinguish. The first red segment above
shaped symbols indicate the limit above or below which the green segments will illuminate at or just below the
continuous operation is likely to cause damage or respective maximum limit. The correponding digital
shortened life. The YELLOW/WHITE markings indicate display and MFD should be checked to determine
the range when special attention should be given to the whether a limit has been exceeded.
operation covered by the display.
c. Numerical Limitations. For limitations where a
The S marking by the TGT display indicates the number is duplicated in two successive ranges, the
maximum momentary (1 second) temperature during number that is duplicated is included in the lower
start. The T marking on the TGT display indicates the range. To enter the higher range the displayed/
maximum momentary (1 second) transient temperature recorded value must exceed the duplicate number. For
during continuous operation. example, for engine torque 0 - 100% Continuous, 100 -
b. Vertical Scales. The scales have blue, green, 112 30 minute limit. A displayed/recorded value of
and red light segments for NP and TRQ and blue, 100% is included in the continuous range; any value
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：OPERATOR’S MANUAL FOR ARMY OH-58D HELICOPTER 2(54)