(2)
On the ECAM control panel push the COND pushbutton switch.
(3)
Adjust the temperature simulating devices until on the ECAM lower DU the CKPT, the FWD cabin and the AFT cabin temperatures show 16 deg.
C.
(4)
On the AIR COND panel 30VU:
(a) Make sure that:
-
the X BLEED selector is at the AUTO position,
-
the PACK 1 and the PACK 2 pushbutton switches are in the on position (the FAULT and the OFF legends are off).
(5)
After 3 minutes:
(a) On the panels 22VU and 30VU push the HOT AIR pushbutton switches to the off position (the OFF legends come on).
(6)
On the AIR COND panel 30VU turn the COCKPIT, the FWD CABIN and the AFT CABIN temperature selectors to the HOT position.
R 1EFF : 001-003, 051-054, 1 21-00-00Page A213 1 1 Aug 01/05 1 1 1CES 1
(7)
Move the applicable throttle control lever forward until on the ECAM upper DU a N2 of 95% is shown.
(8)
Keep this condition for 15 minutes. NOTE : During this 15 minute period you must constantly monitor the
____
pack temperatures.
(9)
To do this you must:
(a)
On the ECAM control panel push the BLEED pushbutton switch.
(b)
On the ECAM lower DU make sure that:
-
the pack compressor outlet temperature does not go above 230 deg. C maximum (max.) and
-
the pack outlet temperature does not go above 85 deg. C (max.). NOTE : If any of the temperatures go above max. you must stop the
____ procedure and do the trouble shooting of the ECS (refer to TSM, chapter 21).
(10)
Move the applicable throttle control lever to the idle position.
(11)
On the ECAM control panel push the COND pushbutton switch.
(12)
Adjust the temperature simulating devices until on the ECAM lower DU the CKPT, the FWD cabin and the AFT cabin temperatures show 30 deg.
C.
(13)
On the AIR COND panel 30VU turn the COCKPIT, the FWD CABIN and the AFT CABIN temperature selectors to the COLD position.
(14)
Move the applicable throttle control lever forward until on the ECAM upper DU a N2 of 95% is shown.
(15)
Keep this condition for 15 minutes. NOTE : During this 15 minute period you must also constantly monitor
____ the pack temperatures as in work step (7) of this paragraph.
(16)
Move the applicable throttle control lever to the idle position.
(17)
On the ECAM control panel push the COND pushbutton switch.
(18)
Adjust the temperature simulating devices until on the ECAM lower DU the CKPT, the FWD cabin and the AFT cabin temperatures show 16 deg.
C.
R 1EFF : 001-003, 051-054, 1 21-00-00Page A214 1 1 Aug 01/05 1 1 1CES 1
(19)
On the AIR COND panel 30VU turn the COCKPIT, the FWD CABIN and the AFT CABIN temperature selectors to the HOT position.
(20)
Move the applicable throttle control lever forward until on the ECAM upper DU a N2 of 95% is shown.
(21)
Keep this condition for 15 minutes. NOTE : During this 15 minute period you must constantly monitor the
____ pack temperatures as in work step (7) of this paragraph.
R **ON A/C 004-049, 055-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 21-00-00-160-060-A
J. Stage 1 Cleaning of the ECS WARNING : BE CAREFUL WHEN YOU DO THIS CLEANING PROCEDURE. A VERY STRONG
_______ HOT OR COLD AIRFLOW WILL OCCUR IN THE AREA OF THE PACK BAY. THIS AIRFLOW CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING : MAKE SURE THAT THERE ARE NO PERSONS OR EQUIPMENT NEAR THE RAM
_______ AIR OUTLETS. HOT EXHAUST GASES CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
CAUTION : MAKE SURE THAT THE AREA NEAR THE RAM AIR INLET IS CLEAN AND
_______ FREE FROM LOOSE ARTICLES. LOOSE ARTICLES CAN GO INTO THE RAM AIR INLET AND CAUSE DAMAGE TO EQUIPMENT.
NOTE : Make sure that at least one of the windows in the cockpit stays
____ open during this part of the decontamination procedure.
(1)
Start the engine 1(2) (Ref. TASK 71-00-00-710-003).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 1(97)
