(2)
 On the ECAM control panel push the COND pushbutton switch.

 (3)
 Adjust the temperature simulating devices until on the ECAM lower DU the CKPT, the FWD cabin and the AFT cabin temperatures show 16 deg.

 C.

 (4)
 On the AIR COND panel 30VU:

 (a) Make sure that:
 -
the X BLEED selector is at the AUTO position,

 -
the PACK 1 and the PACK 2 pushbutton switches are in the on position (the FAULT and the OFF legends are off).

 (5)
 After 3 minutes:

 (a) On the panels 22VU and 30VU push the HOT AIR pushbutton switches to the off position (the OFF legends come on).

 (6)
 On the AIR COND panel 30VU turn the COCKPIT, the FWD CABIN and the
 AFT CABIN temperature selectors to the HOT position.

 (7)
 Move the applicable throttle control lever forward until on the ECAM upper DU a N2 of 95% is shown.

 (8)
 Keep this condition for 15 minutes. NOTE : During this 15 minute period you must constantly monitor the

____
 pack temperatures.

 (9)
 To do this you must:

 (a)
 On the ECAM control panel push the BLEED pushbutton switch.

 (b)
 On the ECAM lower DU make sure that:

 -
the pack compressor outlet temperature does not go above 230 deg. C maximum (max.) and

 -
the pack outlet temperature does not go above 85 deg. C (max.). NOTE : If any of the temperatures go above max. you must stop the

____ procedure and do the trouble shooting of the ECS (refer to TSM, chapter 21).
 (10)
 Move the applicable throttle control lever to the idle position.

 (11)
 On the ECAM control panel push the COND pushbutton switch.

 (12)
 Adjust the temperature simulating devices until on the ECAM lower DU the CKPT, the FWD cabin and the AFT cabin temperatures show 30 deg.

 C.

 (13)
 On the AIR COND panel 30VU turn the COCKPIT, the FWD CABIN and the AFT CABIN temperature selectors to the COLD position.

R 1EFF : 004-049, 055-099, 101-149, 151-199, 1 21-00-00Page A216 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 (14)
 Move the applicable throttle control lever forward until on the ECAM

 upper DU a N2 of 95% is shown.

 (15)
 Keep this condition for 15 minutes. NOTE : During this 15 minute period you must also constantly monitor

____ the pack temperatures as in work step (7) of this paragraph.

 (16)
 Move the applicable throttle control lever to the idle position.

 (17)
 On the ECAM control panel push the COND pushbutton switch.

 (18)
 Adjust the temperature simulating devices until on the ECAM lower DU the CKPT, the FWD cabin and the AFT cabin temperatures show 16 deg.

 C.

 (19)
 On the AIR COND panel 30VU turn the COCKPIT, the FWD CABIN and the AFT CABIN temperature selectors to the HOT position.

 (20)
 Move the applicable throttle control lever forward until on the ECAM upper DU a N2 of 95% is shown.

 (21)
 Keep this condition for 15 minutes. NOTE : During this 15 minute period you must constantly monitor the

____ pack temperatures as in work step (7) of this paragraph.
 **ON A/C ALL
 Subtask 21-00-00-860-078
 K. Stop the engine 1(2) (Ref. TASK 71-00-00-710-028).
R 1EFF : ALL 1 21-00-00Page A217 1 1 Aug 01/05 1 1 1CES 1 Subtask 21-00-00-865-078

 L. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
R  **ON A/C 401-499,
 49VU AIR COND/TEMP CTL/SYS 1 CHAN B/28VDC  52HH  D08 
R  **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
 122VU AIR COND/PACK TEMP/CTL SYS1/2/115VAC  21HH  W22
 122VU AIR COND/PACK TEMP/CTL SYS1/2/28VDC  23HH  W21
 122VU AIR COND/PACK TEMP/CTL SYS1/1/115VAC  1HH  X22
 122VU AIR COND/PACK TEMP/CTL SYS1/1/28VDC  3HH  X21
 122VU AIR COND/PACK TEMP CTL SYS2/2/28VDC  24HH  Y21
 122VU AIR COND/PACK TEMP CTL SYS2/2/115VAC  22HH  Y20 
R 
R  **ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-302, 
R  122VU AIR COND/PACK TEMP CTL SYS2/1/28VDC  4HH  Y19 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 1(98)