__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific warning notice
No specific access platform 1.6 m (5 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
26-12-34-991-001 Fig. 401
3. Job Set-up
__________ Subtask 26-12-34-941-050
A. Safety Precautions
(1) In the cockpit, on the ENG panel 115VU, put a warning notice to tell the persons not to start the engine .
Subtask 26-12-34-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 2WD1
49VU ENGINE/1/FIRE DET/LOOP A 7WD1 A06 121VU ENGINE/ENG1/FIRE DET/LOOP B 8WD1 Q38 FOR 2WD2 49VU ENGINE/2/FIRE DET/LOOP B 8WD2 A07 121VU ENGINE/ENG2/FIRE DET/LOOP A 7WD2 Q39
Subtask 26-12-34-010-050
C. Get Access
(1)
Put the access platform in position.
(2)
Open the access door 824.
4. Procedure
_________
(Ref. Fig. 401/TASK 26-12-34-991-001) Subtask 26-12-34-020-050
A. Remove the Fire Detection Unit (FDU):
(1)
Disconnect the electrical connectors (5) and (6) from the Fire Detection Unit (1).
(2)
Put blanking caps on the electrical connectors (5) and (6).
(3)
Remove the screws (2) and the washers (3).
(4)
Remove the fire detection unit (1).
Engine Fire-Detection Unit (FDU)
Figure 401/TASK 26-12-34-991-001
1EFF : ALL 1 26-12-34 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 26-12-34-400-001
Installation of the Engine Fire-Detection Unit (FDU) (2WD1,2WD2)
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R R 26-12-00-710-001 26-12-00-710-002 31-60-00-860-001 31-60-00-860-002 52-41-00-410-002 26-12-34-991-001 Operational Check of Loop/Squib Operational Test of the Engine Fire and Overheat Detection with the Centralized Fault Display System (CFDS)EIS Start ProcedureEIS Stop ProcedureClose the Avionics Compartment Doors after AccessFig. 401
3. Job Set-up__________
Subtask 26-12-34-860-050
A. In the cockpit, on the ENG panel 115VU, make sure that the warning notice is in position to tell persons not to start the engines.
Subtask 26-12-34-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 2WD1
49VU ENGINE/1/FIRE DET/LOOP A 7WD1 A06 121VU ENGINE/ENG1/FIRE DET/LOOP B 8WD1 Q38 FOR 2WD2 49VU ENGINE/2/FIRE DET/LOOP B 8WD2 A07 121VU ENGINE/ENG2/FIRE DET/LOOP A 7WD2 Q39
4. Procedure
_________
(Ref. Fig. 401/TASK 26-12-34-991-001)
Subtask 26-12-34-420-050
A. Install the Fire Detection Unit (FDU):
(1)
Put the Fire Detection Unit (1) on its support (4).
(2)
Install the washers (3), the screws (2) and tighten them.
(3)
Remove the blanking caps from the electrical connectors (5) and (6).
(4)
Make sure that the electrical connectors are clean and in the correct condition.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FIRE PROTECTION 防火1(50)
