-
FOR 6028CM
 remove 522AB, 522CB

 -
FOR 6036CM
 remove 522LB, 522NB

 -
FOR 6038CM

 1EFF : ALL 1 27-84-45Page 451 1 1 May 01/98R 1 1 1CES 1

 remove 522NB, 522QB
 -
FOR 6040CM
 remove 522QB, 522SB

 -
FOR 6042CM
 remove 522SB

 -
FOR 6044CM
 remove 522UB

 -
FOR 6064CM
 remove 621CB, 621EB

 -
FOR 6078CM
 remove 622AB, 622CB

 -
FOR 6086CM
 remove 622LB, 622NB

 -
FOR 6088CM
 remove 622NB, 622QB

 -
FOR 6090CM
 remove 622QB, 622SB

 -
FOR 6092CM
 remove 622SB

 -
FOR 6094CM
 remove 622UB.

 4. Procedure
_________
 (Ref. Fig. 402/TASK 27-84-45-991-002)
 Subtask 27-84-45-020-055
 A. Removal of the Torque Shafts
 (1)
 Install a LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001) (Ref. TASK 27-50-00-400-003): - on the torque shaft, inboard of the applicable component - on the torque shaft, outboard of the applicable component.

 (2)
 Remove the nuts (2), the bolts (4) and the shaft (3).

 (3)
 Remove the universal joint (1).

 (4)
 Remove the retaining ring (6), the pin (7) and the universal joint (5).

 1EFF : ALL 1 27-84-45Page 452 1 1 May 01/98R 1 1 1CES 1

 TASK 27-84-45-400-007
 Installation of the Torque Shafts 6014CM(6064CM)/6028CM(6078CM)/6036CM
 (6086CM)/6038CM(6088CM)/6040CM(6090CM)/6042CM(6092CM)/6044C M(6094CM)

 WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
 NOTICES ARE IN POSITION.

 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific safety barriers
 No specific warning notice
 No specific Torque Wrench : range 0.20 to 3.60 m.daN

 (2.00 to 26.00 lbf.ft) 98D27504030001 2 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-018
 GENERAL PURPOSE ASSEMBLY PASTE (Ref. 20-31-00)

 Material No. 04-022  USA MIL-PRF-81322 GRADE 2
 SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
 (Ref. 20-31-00)

 Material No. 11-026 GB DEF-STAN 68-148/1 R SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
 Material No. 15-007  AIB TN 10138 TYPE II GRADE 1 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
 Material No. 19-003  USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and
 Slats (98D27504030001)
 27-80-00-866-005 Retracting the Slats on the Ground
 27-84-00-710-001 Operational Test of the Slat System
 27-84-45-991-001 Fig. 401

R 27-84-45-991-002 Fig. 402
 3. Job Set-up
__________
 (Ref. Fig. 401/TASK 27-84-45-991-001)
 Subtask 27-84-45-941-063

 A. Safety Precautions
 (1)
 Make sure that the safety barriers are in position.

 (2)
 Make sure that the warning notice is in position to tell persons not to operate the slat controls.

 Subtask 27-84-45-860-056
 B. Aircraft Maintenance Configuration
 (1)
 Make sure that the slats are retracted fully (Ref. TASK 27-80-00-866-005).

 (2)
 Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER is installed on the flap/slat control lever on panel 114VU.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱7(140)