R 1. Set the test set (or bench) for: On the test set:
R Heading and Speed report BDS 6.0 The results must show:
R test
R - Baro Altitude rate - 0 ft/min
R - Inertial vertical velocity - 0 ft/min
R - Indicated Air speed - 0 kt
R - Magnetic Heading - Magnetic Heading of the aircraft
R - Mach number - 0
R 1EFF : 106-149, 221-299, 301-399, 401-499, 1 34-52-00Page 535 1 1 Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R 2. Set the test set (or bench) for: On the test set:
R Track and Turn report BDS 5.0 The results must show:
R test
R - Roll angle - X degrees (X is a number that shows
R approximately the roll of the aircraft)
R - True Airspeed - 0 kt
R - Ground speed - 0 kt
R - True track angle - Heading of the aircraft
R - Track angle rate - 0 degree/second
R 3. In the center of the FCU:
R Turn the altitude selector knob
R to set an altitude of 10,000 ft
R in the ALT field of the display
R window and pull the altitude
R selector knob.
R 4. Set the test set (or bench) for: On the test set:
R Selected Vertical Intention BDS The result must show:
R 4.0 test
R - Barometric Pressure setting - 1013 hPa
R - FCU selected altitude - 10,000 ft.
R R (2) Put the aircraft back to ground configuration (Ref. TASK 32-00-00-860-002).
R **ON A/C ALL
5. Close-up________
Subtask 34-52-00-860-096
A. Put the aircraft back to its initial configuration.
(1) On the center pedestal, on the ATC/TCAS control unit, set: - the ALT RPTG ON/OFF switch to OFF - the ON/AUTO/STBY switch to STBY.
(2) Do the ADIRS Stop Procedure(Ref. TASK 34-10-00-860-005).
1EFF : ALL 1 34-52-00Page 536 1 1 Aug 01/05 1 1 1CES 1
(3)
Remove the test antenna and the test set.
(4)
De-energize the aircraft electrical circuits
(Ref. TASK 24-41-00-862-002).
Subtask 34-52-00-080-051
B. Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 34-52-00Page 537 1 1 Aug 01/05 1 1 1CES 1
TASK 34-52-00-720-006 Functional Test of the ATC Antennas
1. Reason for the Job
__________________
Refer to the MPD TASK: 345200-02
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform No specific telescopic pole No specific ATC grount test unit
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power
3. Job Set-up
__________ Subtask 34-52-00-861-055
A. Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002). Subtask 34-52-00-865-059
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU COM NAV/ATC/1 5SH1 G11 121VU COM NAV/ATC/2 5SH2 K07
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航4(136)
