F 『
E C F M E
E E
E 56-5B E
E E
Rubbed Scarfed Scuffed Uneven Weak.
F 『 EEFF : ALL E Page 1270-00-00
E E Feb 01/98 E E ECES E PRECAUTIONARY MEASURES TO BE TAKEN DURING REMOVAL/INSTALLATION
F 『
E C F M E
E E
E 56-5B E
E E
______________________________________________________________ MAINTENANCE PRACTICES
_____________________
TASK 70-11-00-918-002
Precautionary Measures to be taken during Removal/Installation Operations
1. Reason for the Job
__________________
Special care must be taken each time maintenance operations are performed in engine critical areas. Extensive damage can result from foreing objects entering the engine (FOD) or from engine parts that are not properly secured. It is especially important that all critical areas at the engine and its immediate surrounding area be checked for cleanliness before each engine run.
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
70-21-00-918-002 Seals (Preformed Packings and O-rings) and Gaskets
3. Job Set-up
__________
Subtask 70-11-00-869-055
A. Not applicable.
4. Procedure
_________
Subtask 70-11-00-869-053
A. Engine Critical Areas.
(1) Air inlet cowl.
(2) Bleed valve compartments.
(3) Interfaces with customer bleeds.
F 『 EEFF : ALL E Page 20170-11-00
E E Feb 01/98 E E ECES E Subtask 70-11-00-869-054
F 『
E C F M E
E E
E 56-5B E
E E
B. General Precautions.
WARNING : SOME PARTS (MOSTLY LOOP CLAMPS) INSTALLED ON ENGINES MAY
_______ CONTAIN SMALL AMOUNTS OF ASBESTOS. THE P/N OF THESE PARTS IS MARKED WITH AN ASTERISK IN THE ALPHA/NUMERIC INDEXES OF THE ENGINE MANUFACTURER'S ILLUSTRATED PARTS CATALOG (IPC). REVIEW THE ENGINE MANUFACTURER'S IPC TO DETERMINE IF PARTS ON YOUR ENGINE ARE AFFECTED. IF YOU REPLACE OR HANDLE THESE PARTS, WEAR APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT AND STRICTLY OBEY ALL APPLICABLE ENVIRONMENTAL CONTROLS AND REGULATIONS FOR HANDLING, REPLACING AND DISPOSING OF ASBESTOS CONTAINING HARDWARE.
(1) Before performing maintenance ensure the following have been accomplished:
(a) Pockets of working clothes have been emptied of their contents.
(b) Soles of footwear are clean.
(c) All critical areas of engine and its immediate surroundings are free of non-essential tools and materials.
(2) After completion of maintenance ensure the following have been accomplished:
(a) All tools and non-installed engine parts are removed.
(b) All clamps and brackets are secured.
(c) All loose wire (instrumentation and lockwire) are removed.
(d) Check that the vicinity of the air inlet cowl, and customer bleeds are clear of any foreign bodies. Use a vacuum cleaner to clean zones difficult to reach.
(e) Check that protective covers are installed.
F 『 EEFF : ALL E Page 20270-11-00
E E Feb 01/98 E E ECES E Subtask 70-11-00-918-052
F 『
E C F M E
E E
E 56-5B E
E E
C. Removal of components and accessories.
(1) The practices related to seals are in chapter (Ref. TASK 70-21-00-918-002).
(2) Protect components and accessories againts mechanical contact with metallic tools before removal.
(3) Protect openings with clean covers/caps, as required during removal of a component or accessory.
(4) Protect the electrical connections when electrical systems are disconnected.
(5) Protect all protruding ends such as the gearshafts and connections when removing a components.
Subtask 70-11-00-918-053
D. Installation of components and accessories. CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STANDARD PRACTICES - ENGINES(7)
