4 Do a check to see if 28VDC is available between the pins as
_
shown in the table that follows.
-------------------------------------------------| SIGNAL LINE | CONNECTOR 10QG-A | |-----------------------------|-------------------| | MOTOR 1 OPEN 28VDC SUPPLY | A | | MOTOR 1 GROUND/EARTH | E | -------------------------------------------------
5 Reconnect the electrical supply connector 10QG-A to the
_ ACTUATOR-LP FUEL VALVE, ENG 2 (10QG).
(b) Disconnect the electrical supply connector 10QG-B from the ACTUATOR-LP FUEL VALVE, ENG 2 (10QG).
1 Do a wiring check (Ref. AWM 28-24-02) of the aircraft wiring
_ (motor 2/ground/earth) between the ACTUATOR-LP FUEL VALVE, ENG 2 free connector 10QG-B, pin E and the ground/earth point 4004VN(622STA450) to make sure a ground/earth is on pin E of connector 10QG-B.
2 Set the ENG/MASTER 2 (2KC) switch to OFF.
_
3 Do a check to see if 28VDC is available between the pins as
_
shown in the table that follows.
-------------------------------------------------| SIGNAL LINE | CONNECTOR 10QG-B | |-----------------------------|-------------------| | MOTOR 2 CLOSE 28VDC SUPPLY | C | | MOTOR 2 GROUND/EARTH | E | -------------------------------------------------
4 Set the ENG/MASTER 2 (2KC) switch to ON.
_
5 Do a check to see if 28VDC is available between the pins as
_
shown in the table that follows.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞28-24-00∞∞∞∞∞∞∞∞∞∞Page 244
Feb 01/98 CES
------------------------------------------------
| SIGNAL LINE | CONNECTOR 10QG-B |
|----------------------------|-------------------|
| MOTOR 2 OPEN 28VDC SUPPLY | A |
| MOTOR 2 GROUND/EARTH | E |
------------------------------------------------
(9) If the 28VDC supplies are:
(a) Correct as given in the tables above: 1 Replace the ACTUATOR-LP FUEL VALVE, ENG 2 (10QG), (Ref. AMM
_ TASK 28-24-51-000-001), and (Ref. AMM TASK 28-24-51-400-001).
2 If the fault continues:
_
- replace the VALVE-LP FUEL, ENG 2 (13QM), (Ref. AMM TASK 28-24-41-000-001), and (Ref. AMM TASK 28-24-41-400-001).
(b) Not correct as given in the tables above:
- remove the ENG/APU FIRE PANEL (1WD) (Ref. AMM TASK 26-12-12-000-001).
(10) Do a check to see if 28VDC is available at connector 1WD-D, pin <H (Ref. AWM 28-24-02).
(11) Do a check to see if 28VDC is available at connector 1WD-C, pin <B (Ref. AWM 28-24-02).
(12) If the 28VDC supplies are:
(a) Correct as given in the Steps (10) and (11): 1 Replace the ENG/APU FIRE PNL (1WD), (Ref. AMM TASK 26-12-12-
_ 000-001), and (Ref. AMM TASK 26-12-12-400-001).
2 Do the test given in Para. 3.A.
_
(b) Not correct as given in the Step (10):
- check/replace C/B-FUEL/LP VALVE/MOT 1/ENG 2 (2QG) (49VU210). 1 Do the test given in Para. 3.A.
_
2 If the fault continues:
_
- do a check (Ref. AWM 28-24-02) of the aircraft wiring between the C/B-FUEL/LP VALVE/MOT 1/ENG 2 (2QG), terminal 2 and the ENG/APU PANEL (1WD) free connector 1WD-D, pin H.
3 Repair all the unserviceable wiring and connectors.
_
4 Do the test given in Para. 3.A.
_
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞28-24-00∞∞∞∞∞∞∞∞∞∞Page 245
Feb 01/98 CES
(c) Not correct as given in the Step (11):
- check/replace C/B-FUEL/LP VALVE/MOT 2/ENG 2 (4QG) (121VU212).
1_ Do the test given in Para. 3.A.
2_ If the fault continues:
- do a check (Ref. AWM 28-24-02) of the aircraft wiring
between the C/B-FUEL/LP VALVE/MOT 2/ENG 2 (4QG), terminal 2
and the ENG/APU PANEL (1WD) free connector 1WD-C, pin B.
3_ Repair all the unserviceable wiring and connectors.
4_ Do the test given in Para. 3.A.
5. Close-up________
A. Put the aircraft back to its initial configuration.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞28-24-00∞∞∞∞∞∞∞∞∞∞Page 246 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 FUEL 燃油2(50)
