- CT-B ELEC PUMP (2706GJ)
- RELAY-N2 SPEED CONDTN (2709GJ)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 29-10-00-200-008
AMM 29-12-00-710-001
AMM 29-12-15-000-001
AMM 29-12-15-400-001
AMM 29-12-17-000-001
AMM 29-12-17-400-001
AMM 29-12-18-000-001
AMM 29-12-18-400-001
AMM 29-12-42-000-001
AMM 29-12-42-400-001
AMM 29-12-51-000-001
AMM 29-12-51-400-001
AMM 29-24-51-000-001
AMM 29-24-51-400-001
AMM 71-00-00-710-003
AMM 71-00-00-710-003
AMM 71-00-00-710-028
ASM 29-12/01
Check Nitrogen Charge Pressure on Hydraulic Power AccumulatorsFunctional Check of Blue Electrical Pump Pressure by Reading ECAM IndicationRemoval of the Blue Electric-Pump Current Transformer (2706GJ)Installation of the Blue Electric-Pump Current Transformer (2706GJ)Removal of the Electric Pump Pressure-Switch (2074GJ)Installation of the Electric Pump Pressure-Switch (2074GJ)Removal of the Blue Electric Pump Phase-Unbalance Detector (2707GJ)Installation of the Blue Electric Pump Phase-Unbalance Detector (2707GJ)Removal of the Blue Power AccumulatorInstallation of the Blue Power AccumulatorRemoval of the Electric Pump (2075GJ)Installation of the Electric Pump (2075GJ)Removal of the Electric Pump (3075GX)Installation of the Electric Pump (3075GX)Engine Automatic StartEngine Automatic StartEngine Shutdown
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞29-12-00∞∞∞∞∞∞∞∞∞∞Page 222
May 01/05R
CES
3. Fault Confirmation
__________________
NOTE : Continue with the step B. when the crew reported that the HYD B ELEC
____ PUMP LO PRESS warning was shown for a short time during the start of the engines.
A. Do the operational test of the Blue hydraulic system (Ref. AMM TASK 29-12-00-710-001).
B. Do the subsequent test when the HYD B ELEC PUMP LO PRESS warning was shown for a short time during the start of the engines.
(1) Start the engine No. 2 (Ref. AMM TASK 71-00-00-710-003).
(2) Start the engine No. 1 (Ref. AMM TASK 71-00-00-710-003).
(3) Look at the upper ECAM DU for the warning HYD B ELEC PUMP LO PRESS.
(4) Shutdown the engines (Ref. AMM TASK 71-00-00-710-028).
4. Fault Isolation
_______________
R A. If the test gives:
R - the HYD B ELEC PUMP LO PR on the upper ECAM DU,
R - the LO flag of the BLUE hydraulic system on the HYD page of the lower
R ECAM DU,
R - the BLUE ELEC PUMP P/BSW FAULT on panel 40VU,
R do the subsequent steps:
R - examine if the Blue electric pump operates.
R (1) If the ELEC PUMP-B (2075GJ) operates:
R - look on the ECAM SD - DU and do a check of the pressure indication:
R (a) If the pressure is less than 1450 psi (99.9739 bar):
R 1_ Do a check of the nitrogen charge pressure of the Blue
R hydraulic power accumulator (Ref. AMM TASK 29-10-00-200-008).
R a_ If necessary, replace the ACCU-B PWR (2070GM) (Ref. AMM
R TASK 29-12-42-000-001) and (Ref. AMM TASK 29-12-42-400-R 001).
R 2_ If the fault continues:
R a_ Replace the ELEC PUMP-B (2075GJ) (Ref. AMM TASK 29-12-51-R 000-001) and (Ref. AMM TASK 29-12-51-400-001).
R NOTE : Replace the ELEC PUMP-B (2075GJ) with the ELEC
____ R PUMP-Y (3075GX) which is interchangeable, if a new R pump is not available (Ref. AMM TASK 29-24-51-000-R 001) and (Ref. AMM TASK 29-24-51-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : ALL ∞∞29-12-00∞∞∞∞∞∞∞∞∞∞Page 223
May 01/05 CES
R (b) If the pressure is more than 1450 psi (99.9739 bar):
R - do a check for continuity between:
R PRESS SW-ELEC PUMP, B (2074GJ) connector A/A and connector A/C
R and repair the wiring as necessary (Ref. ASM 29-12/01).
R 1_ If there is continuity:
R - replace the PRESS SW-ELEC PUMP, B (2074GJ) (Ref. AMM TASK
R 29-12-17-000-001) and (Ref. AMM TASK 29-12-17-400-001).
R 2_ If there is no continuity:
R - do a check of the wiring for a GND connection between:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 液壓(44)
