R AMM 29-19-51-000-003 Removal of the Leakage-Measurement Solenoid Valve
R (3150GP)
R AMM 29-19-51-400-003 Installation of the Leakage-Measurement Solenoid
R Valve (3150GP)
AMM 29-23-00-860-001 Disconnection of the Isolation Coupling of the Power Transfer Unit (PTU) AMM 29-23-00-860-002 Connection of the Isolation Coupling of the Power Transfer Unit (PTU) AMM 29-24-00-863-001 Pressurize the Yellow Hydraulic System with the
Electric Pump AMM 29-24-00-864-001 Depressurize the Yellow Hydraulic System AMM 29-32-12-000-003 Removal of the System Pressure Switch (3151GN) AMM 29-32-12-400-003 Installation of the System Pressure Switch (3151GN) ASM 29-19/01 ASM 29-24/01 ASM 29-32/01 ASM 31-52/02
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞29-13-00∞∞∞∞∞∞∞∞∞∞Page 223
May 01/02 CES
3. Fault Confirmation
__________________
A. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/SOL VALVES/G/Y/B/LEAK/TST 1881GP N35 121VU HYDRAULIC/Y HYD/PUMP ENG2/MONG 3700GD Q37 121VU HYDRAULIC/Y HYD/PUMP ENG2/CTL 3701GD Q36
B. Aircraft Maintenance Configuration
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES
_______ ARE CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
(1) Disconnect the isolation coupling of the PTU (Ref. AMM TASK 29-23-00-860-001).
(2) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(3) On panel 50VU, make sure that the HYD/LEAK MEASUREMENT VALVES/Y pushbutton switch is set to on (OFF light not on).
(4) Pressurize the Yellow hydraulic system from a ground supply or with the Yellow electric pump (Ref. AMM TASK 29-10-00-863-002) or (Ref. AMM TASK 29-24-00-863-001).
(5) Look for fault indications on the lower ECAM DU.
4. Fault Isolation
_______________
A. If the fault confirmation gives:
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
- the system name and the flow arrow of the Yellow hydraulic system in amber on the lower ECAM DU:
- do a check of the system pressure on the lower ECAM DU and on the system accumulator gage (3072GM).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞29-13-00∞∞∞∞∞∞∞∞∞∞Page 224
May 01/02R
CES (1) If the system pressure is more than 1450 psi:
- use the rudder pedals to operate the rudder.
(a) If the rudder operates:
- do a check for continuity between the: the PRESS SW-FLT CTL, Y (3151GN) connector A/A and the connector A/C (with the hydraulic system pressurized) (Ref. ASM 29-32/01).
1 If there is continuity:
_
- replace the PRESS SW-FLT CTL, Y (3151GN) (Ref. AMM TASK 29-32-12-000-003) and (Ref. AMM TASK 29-32-12-400-003).
2 If there is no continuity:
_
- do a check and repair the wiring between the: PRESS SW-FLT CTL, Y (3151GN) connector A/C and FWC-1/ FWC-2 connector AD/06E (Ref. ASM 29-32/01) and (Ref. ASM 31-52/02).
(b) If the rudder does not operate:
- do a check for 28 VDC at the: the SOL VALVE-LEAKAGE MEAS, Y (3150GP) connector A/A and the connector A/B. (Ref. ASM 29-19/01).
NOTE : There is normally 0 VDC.
____
1 If there is 28 VDC:
_
- do a check for 28 VDC between: the relay (3811GX) connector X1 and X2.
a If there is 28 VDC:
_
- do a check and repair the wiring between the: relay (3811GX) connector X1 and the HYD YELLOW ELEC PUMP pushbutton switch (3804GX) connector A3 (Ref. ASM 29-19/01) and (Ref. ASM 29-24/01).
b If there is no 28 VDC:
_
- replace the CTL RELAY (3811GX).
(c) If the fault continues:
- replace the TIME DELAY RELAY (3816GX).
(d) If the fault continues:
- replace the TIME DELAY RELAY (6MJ).
(e) If the fault continues:
- do a check for 28 VDC between: the pushbutton switch (1883GP) connector C2 and the connector C3.
1 If there is continuity:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 液壓(68)
