26-21-31
 ALL  ú ú 02 Page 201 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 3)  CONTROL CABIN LIGHTING INDICATOR LIGHTS MASTER DIM BUS (nine circuit breakers)
 S 862-046
 WARNING: DO NOT TOUCH THE SQUIB BEFORE YOU DO THE PROCEDURES FOR DEVICES
_______ THAT ARE SENSITIVE TO ELECTROSTATIC DISCHARGE. ELECTROSTATIC DISCHARGE CAN CAUSE THE FIRE BOTTLE TO RELASE ITS CONTENTS SUDDENLY AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (2)  
Before you touch the squib, do the procedure for devices that are sensitive to electrostatic discharge (AMM 20-40-12/201).

 S 032-003

 (3)  
Remove the electrical connector from the squib.

 S 862-004

 (4)  
Put a cap or metal foil over the squib connector.

 S 032-005

 (5)  
Remove the lockwire from the squib.

 S 022-006

 (6)  
Remove the squib from the bottle.

 S 862-007

 (7)  
Put caps on the squib and the bottle fitting.

 S 212-008

 (8)  
Examine the squib for wear or damage.

 (a)  Make sure there is no damage to the soft seal which prevents damage to the explosive charge.
 NOTE: The soft seal is opposite the electrical connector.
____
 (b)  
If there is damage to the seal, replace it.

 (c)  
If there is corrosion on the squib threads, replace the squib.

 S 212-009
 (9)  Examine the squib service date and make sure the squib is not expired.
 TASK 26-21-31-402-010
 3.  Install the Squib
_________________
 A.  General
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-21-31
 ALL  ú ú 02 Page 202 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 B.
C.
D.
E.
F.
A 737-300/400/500MAINTENANCE MANUAL
 WARNING: MAKE SURE THERE ARE CAPS OR SHUNT PLUGS INSTALLED ON THE SQUIBS
_______ WHEN YOU TOUCH OR MOVE THE SQUIBS. THE SQUIB IS AN EXPLOSIVE DEVICE AND CAN CAUSE INJURY IF IT IS ACCIDENTALLY FIRED.
 (1)  
To prevent incorrect squib connections, do the removal and

 installation procedures for each squib, one at a time.Standard Tools and Equipment

 (1)
Conductive rubber shunt plugs (supplied with the squibs)References

 (1)
AMM 24-22-00/201, Manual ControlAccess

 (1)  
Location Zones 216 Left Main Wheel Well 101/102 Control Cabin

Procedure
 S 432-011
 (1)  
Remove the caps on the squib and the bottle fitting.

 S 422-012

 (2)  
Install the squib to the bottle fitting.

 (a)  Tighten the squib to 90 - 100 pound-inches.
 S 432-013
 (3)  
Install the lockwire to the squib.

 S 432-014

 (4)
Remove the cap or metal foil from the squib.Installation Check

 S 862-015

 (1)  
Make sure the four squib electrical connectors on the engine extinguisher bottles are disconnected.

 S 862-016

 (2)  
Make sure the conductive rubber shunt plugs are installed across the pins of each squib.

 S 862-017

 (3)  
Supply electrical power (AMM 24-22-00/201).

 S 862-040

 (4)  
Close these circuit breakers:

 (a)  P6 Load Control Center Panel
 1) EXTINGUISHER BOTTLES RIGHT
 2) EXTINGUISHER BOTTLES LEFT
 3) EXTINGUISHER BOTTLE RIGHT
 4) EXTINGUISHER BOTTLE LEFT

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-21-31
 ALL  ú ú 01 Page 203 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 防火 FIRE PROTECTION(101)