12-21-19
ALL ú ú 01 Page 301 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
UPPER GIMBAL
SEE B
SEE A
DRIVE
MECHANISM
SEE C
SEE D UPPER GIMBAL
A
ZERK
MIL-G-23827
(2 LOCATIONS) 1 (FORWARD AND AFT)
BALLNUT SCREW ZERK
MIL-G-23827
(1 LOCATION) (FORWARD)
UPPER GIMBAL
5 POINTS
B
1 ONE MORE LOCATION IS ON THE OPPOSITE SIDE SHOWN. Stabilizer Control System Lubrication Figure 301 (Sheet 1)
LUBRICATION VENT PLUG
1
UPPER GIMBAL SAFETY SHAFT ZERK
MIL-G-23827
(2 LOCATIONS)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
12-21-19
ALL ú ú 01 Page 302 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
STABILIZER JACKSCREW
DIFFERENTIAL
HOUSING HYDRAULIC BRAKES DRIVE MECHANISM
FILL
MIL-H-5606
1 (2 LOCATIONS)
ANTIROTATION CABLE
LOWER GIMBAL
HYDRAULIC MOTORS
2 POINTS
D
Stabilizer Control System Lubrication Figure 301 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
12-21-19
ALL ú ú 01 Page 303 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
LOWER GIMBAL
SAFETY PIN
LOWER GIMBAL
1 SAFETY SHAFT
ZERK
HYDRAULIC MIL-G-23827
MOTORS (2 LOCATIONS) LOWER GIMBAL
ZERK
STABILIZER TRIM MIL-G-23827
DRIVE MECHANISM 1 (2 LOCATIONS)
4 POINTS
C
A 747-400 MAINTENANCE MANUAL
S 863-003
(2) Pressurize the hydraulic systems No. 2 or 3 (Ref 29-11-00/201).
S 013-005
(3) Open the 312A access door (Ref 06-09-07/201).
S 643-024
(4) Lubricate the safety shafts of the upper and lower gimbal (Fig. 301).
S 643-025
(5) Lubricate the upper and lower gimbals (Fig. 301).
S 643-006
(6) Lubricate the jackscrew upper ballnut and the stabilizer trim jackscrew (Fig. 301). (a) Hold the STAB TRIM ALTN switches to APL NOSE DN until the stabilizer position indicators show APL NOSE DN. (b) Set the STAB TRIM 2 and 3 switches on the control stand to CUTOUT.
(c) Lubricate the ballnut zerk fitting until the grease goes out of the two lower drain holes.
(d) (e) (f) Set the STAB TRIM 2 and 3 switches on the control stand to ON.Use the STAB TRIM ALTN switches on the control stand to set the stabilizer to approximately 3 units of trim.Set the STAB TRIM 2 and 3 switches on the control stand to CUTOUT.
(g) Lubricate the ballnut zerk fitting until the grease goes out of the two lower drain holes.
(h) (i) (j) Set the STAB TRIM 2 and 3 switches on the control stand to ON.Use the STAB TRIM ALTN switches on the control stand to set the stabilizer to approximately 6 units of trim.Set the STAB TRIM 2 and 3 switches on the control stand to CUTOUT.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
12-21-19
ALL ú ú 01 Page 304 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(k)
Lubricate the ballnut zerk fitting until the grease goes out of the two lower drain holes.
(l)
Set the STAB TRIM 2 and 3 switches on the control stand to ON.
(m)
Use the STAB TRIM ALTN switches on the control stand to set the stabilizer to approximately 9 units of trim.
(n)
Set the STAB TRIM 2 and 3 switches on the control stand to CUTOUT.
(o)
Lubricate the ballnut zerk fitting until the grease goes out of the two lower drain holes.
