(a)  
If any of the following is found, repair or replace the connector. 1) Corrosion or pitting of the contacts. 2) Burn marks on the contacts. 3) Bent or pushed back contacts. 4) Damage or corosion to the connector body.

 S 766-066
 (2)  
Check the battery power connector as follows:

 (a)  
Remove the two (2) bolts that hold the connector together.

 (b)  
If any of the following conditions are found, replace the main battery connector. 1) Corrosion and pitting of the power contacts or terminal lug

 mating surfaces . 2) Excessive free play or broken pins on the handwheel-worm assembly. 3) Burn marks on the power contacts, terminal lug contact bar mating surfaces or terminal stud.

 (c)  
Check the resiliency of the battery connector power contactor as follows: 1) Put the .385 end of the tool into the power contact.

 a)  Make sure the fit is snug and it requires a (1) one pound force to remove the tool.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-31-01
 ALL  ú ú 02 Page 604 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 (d)

(e)

(f)

(g)

(h)

(i)

(j)

(k)

A
747-400 MAINTENANCE MANUAL
Check the ability for the power contact to mate with a worn or
 undersize pin.
 1) Insert the 0.370 end of the tool in the power contact.

 a) Make sure the fit is snug and it requires a (1) one
 pound force to remove the tool.Check the contact bar as follows: 1) If the contact bar is held on with a screw, make sure the
 screw is tight and the contact bar is tight.
 NOTE: Use the standard torque values for the screw
____
 (AMM 20-51-01/201).

 2)  If the contact bar is held with a rivet, make sure the contact bar can not be removed from the connector.
 NOTE: The contact bar is loose on the connector.
____
If the terminal lug or stud is damaged, deformed, discolored or annealed, repair or replaced the terminal lug (SWPM 20-30-00).
 NOTE: If the terminal lug is annealed, use a high temperature
____ terminal lug to replace the lug (SWPM 20-30-11).
Make sure the terminal nuts are tight.
 NOTE: Use the standard torque values for the terminal nut
____ (AMM 20-51-01/201).
 NOTE: Do not pull or move the wires after the terminal nut is
____ tightened.
Put the connector togerther and install the two (2) bolts.
 NOTE: Use the standard torque values for the bolts
____ (AMM 20-51-01/201).
Make sure the wires are centered in the connector openings.
Connect the battery sensor connector (DM7423B) to the battery.
Put the main battery connector into the main battery receptacle
 on the main battery.
 1) Turn the knob on the connector clockwise with your hand

 until it is tight.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-31-01
 ALL  ú ú 02 Page 605 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 2)  Attach the sealing wire from the main battery power connector knob to one of the connector bolts. Use the double twist method.
 NOTE:____ Sealing wire is 0.020 copper wire.
 (3)  S 866-056Remove the DO-NOT-CLOSE tags and close these circuit breakers: (a) On the P414 panel: 1) 414P18, MAIN BATTERY CHARGER (b) On the P6 panel: 1) 6K1 MAIN BATTERY HOT BUS CONTROL
 (4)  S 866-040Remove the DO-NOT-OPERATE tag from the BATTERY switch.
 (5)  S 866-057Set the flight compartment clocks to the correct date and Greenwich Mean Time (GMT)(AMM 31-25-00/001).
 (6)  S 716-059Do this task: "Operational Test of the Main Battery" (AMM 24-31-01/501).
 (7)  S 866-060Remove electrical power, if it is not necessary (AMM 24-22-00/201).

 TASK 24-31-01-406-035
 3. APU Battery Connector Examination (Fig. 601)
_________________________________
 A. References
 (1)
AMM 20-51-01/201, Standard Torque Values
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 ELECTRICAL POWER 電源 2(55)