(a)  
Make sure the valve actuator (1) is in the closed position.

 (b)  
Install the valve body (5) so that the TOP position indication is on the bottom of the valve (nearest the wing lower skin).

 (c)  
Engage the valve body (5) with the adapter shaft (3).

 (d)  
Make sure the index marks on the valve body (5) align.

 NOTE: The index marks on the valve body must be on the bottom
____ when the valve is closed (nearest the wing lower skin).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-05
 ALL  ú ú 02 Page 409 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 434-044
 (4)  
Do these steps to install the valve body (5):

 (a)  
Install the bolts (7) and washers (8) (four locations) that attach the valve body (5) to the mounting bracket (6).

 (b)  
AIRPLANES WITH A BARE METAL SURFACE AT THE MOUNTING BRACKET; Apply these protective finishes to any exposed areas on the mounting bracket (6): 1) Alodine 600 (AMM 51-21-04/701) 2) BMS 10-20 Type II primer (AMM 28-11-00/801).

 (c)  
Put lockwire on the bolts (7).

 (d)  
Put new O-rings (9) lightly coated with petrolatum in the couplings (4).

 (e)  
Connect the couplings (4) to the valve body (5) (AMM 28-00-00/201).

 S 284-041
 (5)  AIRPLANES WITH A BARE METAL SURFACE AT THE MOUNTING BRACKET; Measure the bonding resistance between the valve body footprint and the front spar structure (SWPM 20-20-00).
 NOTE: The bonding resistance must not be more than 0.010 ohm.
____
 F. Put the Airplane Back to the Usual Condition
 S 944-047
 (1)  
Close and go out of the fuel tank (AMM 28-11-00/201).

 S 944-050

 (2)  
Install the applicable mid spar access door(s) (if necessary) (AMM 28-11-25/401).

 S 944-051

 (3)  
Install the applicable main tank access door(s) (AMM 28-11-02/401).

 G.
Engine Spar Valve Body Operational Tests

 S 714-029
 (1)  Do this task: Engine Fuel Shutoff Valves (Spar Valves) Operational Test (AMM 28-22-00/501).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-05
 ALL  ú ú 02 Page 410 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 714-027
 (2)  Do this task: Engine Spar Valves - Fuel Transfer Operational Test (AMM 28-22-00/501).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-05
 ALL  ú ú 01 Page 411 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 MAIN TANK BOOST PUMP CONDUIT - REMOVAL/INSTALLATION
___________________________________________________
 1.  General
_______
 A.  This procedure contains instructions to remove and install the No. 1 and 4 main tank boost pump conduit.
 B.  The conduit for the No. 1 and 4 main tank boost pumps are found in the No. 2 and 3 inboard fuel tanks.
 C.  Access to the No. 1 and 4 main tank boost pumps is through the boost pump dry bay access doors.
 TASK 28-22-06-004-004
 2.  Main Tank Boost Pump Conduit Removal (Fig. 401)
____________________________________
 A.  References
 (1)
AMM 06-09-08/201, Wing Access Doors and Panels

 (2)
AMM 27-51-00/201, Trailing Edge Flap

 (3)
AMM 28-11-00/201, Fuel Tanks

 (4)
AMM 28-11-02/401, Main Tank Access Panels

 (5)
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 燃油 FUEL 2(126)