28-22-00
 ALL  ú ú 08 Page 521 ú Feb 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (g)  
Put the FUEL CONTROL switch to the CUTOFF position.

 (h)  
After approximately 15 seconds, look at the auxiliary EICAS display. 1) Make sure this EICAS status message does not show:

 a) FUEL SPAR VALVE 1
 S 715-129
 (7)  
Do the test again for these fuel spar valves:

 (a)  
Engine No. 2 spar valve

 (b)  
Engine No. 3 spar valve

 (c)  
Engine No. 4 spar valve

 G.
Put the Airplane Back to the Usual Condition

 S 865-402
 (1)  
Put the AUTOSTART switch to the ON position (if it is necessary) (located on the engine ignition control/fuel jettison module, -pilots overhead panel, P5).

 S 865-136

 (2)
Close these circuit breakers and remove the DO-NOT-CLOSE tags:

 (a)  
P6, Main Power Distribution Panel
 1) 6H2, FIRE EXTINGUISHER ENG 1&3 A
 2) 6H1, FIRE EXTINGUISHER ENG 1&3 B
 3) 6H4, FIRE EXTINGUISHER ENG 2&4 A
 4) 6H3, FIRE EXTINGUISHER ENG 2&4 B
 5) 6F1, IGN 1 ENG 1
 6) 6F2, IGN 1 ENG 2
 7) 6F3, IGN 1 ENG 3
 8) 6F4, IGN 1 ENG 4
 9) 6G19, STBY IGN ENG 1
 10) 6G20, STBY IGN ENG 2
 11) 6G21, STBY IGN ENG 3
 12) 6G22, STBY IGN ENG 4
 13) 6K19, IGN 2 ENG 1
 14) 6K20, IGN 2 ENG 2
 15) 6K21, IGN 2 ENG 3
 16) 6K22, IGN 2 ENG 4
 17) 6L10, FUEL CONT VALVE ENG 1
 18) 6L11, FUEL CONT VALVE ENG 2
 19) 6L12, FUEL CONT VALVE ENG 3
 20) 6L13, FUEL CONT VALVE ENG 4

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-00
 ALL  ú ú 09 Page 522 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 865-401
 (3)
Close this circuit breaker and remove the DO-NOT-CLOSE tag:

 (a)  
On the power distribution center panel, P414: 1) 414D16, ENG FUEL SW ON IND

 S 865-142
 (4)  Remove the electrical power if it is not necessary
 (AMM 24-22-00/201).

 TASK 28-22-00-705-316
 5.  Fuel Crossfeed Valves - Fuel Transfer Operational Test (Fig. 503)______________________________________________________
 A. General
 (1)  
This task transfers fuel from one tank to another tank through the crossfeed valves to make sure the valves are in the commanded position.

 (2)  
You can test one or all four of the crossfeed valves in this procedure.

 (3)  
This procedure operates the fuel boost pumps in the inboard and outboard main tanks. Make sure the minimum and maximum fuel quantities called out in the prepare for the test procedure are available.

 (4)  
Make sure the leading edge flaps are in the fully retracted position. If the flaps are in the takeoff configuration, the No. 2 and 3 crossfeed valves will be commanded closed by the fuel system management cards (FSMC). The FSMC uses flap position and air/ground inputs to supply the logic for the crossfeed close command.

 (5)  
This task transfers fuel from the engine fuel-feed manifold to the refuel/jettison manifold. Make sure the jettison nozzle valves are closed.

 B.
References

 (1)  
AMM 07-11-08/201, Cargo Handling and Fuel Loading

 (2)  
AMM 12-11-01/301, Fuel Servicing

 (3)  
AMM 24-22-00/201, Manual Control

 (4)  
AMM 27-81-00/201, Leading Edge Flap System

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-00
 ALL  ú ú 07 Page 523 ú Oct 18/00
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 2(87)