(3)  
Remove the electrical power (AMM 24-22-00/201).

 S 014-004

 (4)  
Open the access doors, 521BB or 621BB, of the pressure refuel station.

 S 864-003
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-21-01
 ALL  ú ú 01 Page 401 ú Feb 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 034-005
 (5)  
You must disconnect the fuel line for the manual defuel valve from the receptacle when you remove the outboard refuel receptacle.

 S 034-006

 (6)  
Remove the bolts and the washers (8 locations) that attach the refuel receptacle to the spar.

 S 024-007

 (7)  
Remove the refuel receptacle from the spar and discard the seal.

 S 034-008

 (8)  
Install the dust cap on the spar.

 TASK 28-21-01-404-009
 3.  Refuel Receptacle Installation (Fig. 401)______________________________
 A. Equipment
 (1)  
Bonding Meter (AMM 20-22-01/601)

 B.
References

 (1)  
AMM 12-11-01/301, Fuel Servicing

 (2)  
AMM 20-11-15/401, Bonding Jumpers and Ground Leads

 (3)  
AMM 20-22-01/601, Electrical Bonding

 (4)  
AMM 27-81-00/201, Leading Edge Flap System

 (5)  
AIPC 28-21-05 Fig. 1

 C.
Access

 (1)  
Location Zones
 521 Leading Edge to Front Spar, Left
 621 Leading Edge to Front Spar, Right

 (2)  
Access Panels
 521BB Fueling Station Access Door
 621BB Fueling Station Access Door

 D.
Procedure

 (1)  
Remove the dust cap from the spar.

 (2)  
Clean the mating surfaces on the spar and the refuel receptacle.

 (3)  
Install the new seal on the adapter.

 S 434-010
 S 164-011
 S 434-012
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-21-01
 ALL  ú ú 01 Page 402 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

PRESSURE REFUEL STATION
SEE A
PRESSURE REFUEL STATION
SEE A
OUTBOARD REFUEL  FWD 
WASHER  INBOARD REFUEL  RECEPTACLE 
BONDING  (8 LOCATIONS)  RECEPTACLE  SEE  C 
JUMPER  BOLT  SEE  B 
(8 LOCATIONS) 

PRESSURE REFUEL STATION
A REFUEL RECEPTACLE
FUEL LINE FOR THE MANUAL BONDING
DEFUEL VALVEJUMPER RECEPTACLE
SEAL
CAP
ADAPTER
SEAL INBOARD REFUEL RECEPTACLE
WASHER
B
(8 LOCATIONS)
BOLT CAP (8 LOCATIONS)
ADAPTER
OUTBOARD REFUEL RECEPTACLE
C
Refuel Receptacle Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-21-01
 ALL  ú ú 01 Page 403 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 424-013
 (4)  Hold the refuel receptacle on the spar.
 S 434-014
 (5)  Put the washer, the bonding jumper terminal, and the second washer
 on the bolt that attaches the refuel receptacle to the spar.
 NOTE:____ Do not tighten the bolts at this time.

 S 434-025
 (6)  
Attach the bolt and the bonding jumper to the refuel receptacle (AMM 20-11-15/401).

 S 434-015

 (7)  
Install and symmetrically tighten the remaining bolts and the washers that attach the refuel receptacle to the spar.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 燃油 FUEL 2(33)