(13)
 AIPC 28-22-07 FIG. 1

 (14)
 AIPC 28-22-07 FIG. 2

 (15)
 AIPC 28-22-07 FIG. 15

 (16)
 AIPC 28-22-07 FIG. 16

 (17)
 SWPM 20-20-00, Electircal Bond and Ground

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-07
 ALL  ú ú 01B Page 422 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 E.  Access
 (1)  
Location Zones
 452 Nacelle Strut 1 - Torque Box
 521 Nacelle Strut 1 - Leading Edge to Front Spar
 462 Nacelle Strut 2 - Torque Box
 521 Nacelle Strut 2 - Leading Edge to Front Spar
 472 Nacelle Strut 3 - Torque Box
 621 Nacelle Strut 3 - Leading Edge to Front Spar
 482 Nacelle Strut 4 - Torque Box
 621 Nacelle Strut 4 - Leading Edge to Front Spar

 (2)  
Access Panels
 415 Thrust Reverser Half - Engine 1
 416 Thrust Reverser Half - Engine 1
 521FT Wing Leading Edge Cover - Nacelle Strut 1
 425 Thrust Reverser Half - Engine 2
 426 Thrust Reverser Half - Engine 2
 521CT Wing Leading Edge Cover - Nacelle Strut 2
 435 Thrust Reverser Half - Engine 3
 436 Thrust Reverser Half - Engine 3
 611CT Wing Leading Edge Cover - Nacelle Strut 3
 445 Thrust Reverser Half - Engine 4
 446 Thrust Reverser Half - Engine 4
 621FT Wing Leading Edge Cover - Nacelle Strut 4

 F.  
Install the Fuel Line (from the Engine Disconnect to the Forward Wing Spar) (Fig. 402)

 S 424-041
 (1)  
Put the fuel tube(s) in the strut and hold the tube(s) in the correct position.

 S 424-042

 (2)  
Install the bolts, washers, nuts, end caps, spacers and shims (if used) that attach the clamp blocks to the support brackets (View I).

 NOTE: Do not tighten the clamps at this time.
____
 S 644-043
 (3)  Lubricate the new coupling O-rings with the petrolatum.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-07
 ALL  ú ú 01B Page 423 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 434-044
 CAUTION:_______ DO NOT USE ANY TOOLS TO TIGHTEN THE FUEL LINE FITTINGS.  DAMAGE
 TO THE FITTING COMPONENTS OR LOOSENING OF THE ADJACENT FITTINGS
 CAN OCCUR.

 CAUTION: YOU CANNOT TIGHTEN THE FUEL LINE COUPLING AFTER THE INITIAL
_______ INSTALLATION. YOU MUST INSTALL NEW O-RINGS WHEN YOU TIGHTEN THE FUEL LINE COUPLING OR A FUEL LEAK CAN OCCUR.
 (4)  
FOR THE OUTBOARD STRUTS; Tighten these fuel tube(s) couplings (AMM 28-00-00/201):

 (a)  
Shrouded spar coupling (View F).

 1)  Connect the drain line to the shroud coupling body with the union and a new O-ring.

 (b)  
Shrouded bulkhead coupling (View E). 1) At the bulkhead fitting, tighten the jamnut to a torque value of 920 pound-inches

 2)  Connect the drain line to the shroud coupling body with the union and a new O-ring.

 (c)  
Flexible-full coupling (two locations) (View D).

 S 434-102
 (5)  
FOR THE INBOARD STRUTS; Tighten these fuel tube(s) couplings (AMM 28-00-00/201):

 (a)  
Spar coupling (View H).

 (b)  
Bulkhead coupling (View G).

 1)  At the bulkhead fitting, tighten the jamnut to a torque value of 920 pound-inches.

 (c)  
Flexible-full coupling (three locations) (View D).

 S 434-046
 (6)  Tighten the bolts that attach the fuel tube clamp blocks to the support brackets.
 NOTE: Make sure to replace the shims (if removed) from the support
____ clamps.
 S 434-047
 (7)  
Install the lockwire on the fuel coupling(s).

 S 434-048

 (8)  
Use lockwire to attach the bulkhead fitting jamnut and coupling body to the adjacent bolt on the forward and aft side of the bulkhead structure.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊(cè) 燃油 FUEL 3(12)