(b)  
Do these steps to continue with the fuel transfer operation: 1) Continue to transfer fuel from other tanks (if necessary) 2) Do this procedure: Drain the Remaining Fuel (if necessary) 3) Do this procedure: Put the Airplane Back to the Usual

 Condition.
 G. Main Tank Fuel Transfer
 S 862-389
 (1)  
Do this procedure: Prepare for the Fuel Transfer Operation.

 S 862-390

 (2)  
AIRPLANES WITH A HYDROMECHANICAL SCAVENGE SYSTEM;
 Make sure the scavenge system fuel strainers are removed
 (AMM 28-15-00/201).

 S 652-386

 (3)  
Put these crossfeed valve switches to the ON position:

 NOTE: The switches are found on the fuel management control
____
 module on the pilots' overhead panel, P5.

 (a)  
FUEL X FEED 1

 (b)  
FUEL X FEED 2

 (c)  
FUEL X FEED 3

 (d)  
FUEL X FEED 4

 S 652-387
 (4)  Set the applicable pump switches to the ON position:
 NOTE: The pump switches are on the fuel management control
____
 module on the pilots' overhead panel, P5.

 (a)  Override/jettison pumps:
 1) OVRD 2 MAIN FWD
 2) OVRD 2 MAIN AFT
 3) OVRD 3 MAIN FWD
 4) OVRD 3 MAIN AFT

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-26-00
 ALL  ú ú 08 Page 220 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  Main tank boost pumps:
 1) MAIN 1 FWD and MAIN 1 AFT
 2) MAIN 2 FWD and MAIN 2 AFT
 3) MAIN 3 FWD and MAIN 3 AFT
 4) MAIN 4 FWD and MAIN 4 AFT

 S 212-436
 (5)  
Monitor the main tank fuel transfer operation.

 (a)  
During the fuel transfer operation, the low pressure light for the main tank override/jettison pumps can show.

 NOTE: No maintenance action is necessary.
____
 (b)  
Monitor the refuel quantity indicators to find the fuel quantity in each tank.

 (c)  
Continue the fuel transfer until the indicators show the specified quantity of fuel.

 (d)  
When the fuel level goes below the inlets for the main tank override/jettison pumps, put the override/jettison pump switches to the off position (pump low pressure).

 NOTE: Reference the main tank pump priming graphs
____
 (AMM 28-31-01/401).

 (e)  Use the main tank boost pumps to continue the fuel transfer operation.
 S 652-392
 (6)  
Stop the fuel transfer:

 (a)  
When the main tank fuel quantity is zero, put the main tank boost pump switches to the off position.

 (b)  
Put the switches for the crossfeed valves to the off position.

 (c)  
At the left and right pressure refuel station, do these steps: 1) Put the manual refuel valve switch(es) to the CLOSED

 position. 2) Close the manual shutoff valves for the fueling receptacle. 3) Close the manual defueling valves.

 (d)  
Do these steps to continue with the fuel transfer operation: 1) Continue to transfer fuel from other tanks (if necessary) 2) Do this procedure: Drain the Remaining Fuel (if necessary) 3) Do this procedure: Put the Airplane Back to the Usual

 Condition.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-26-00
 ALL  ú ú 10 Page 221 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 H. Reserve Tank to the Inboard Main Tank Fuel Transfer
 NOTE: Fuel from the reserve tank is transferred to the inboard tank when
____ the reserve tank transfer valves are opened (gravity feed). It is not necessary to open the defuel valve, shutoff valve or refuel valves to transfer fuel (SSM 28-00-01).
 S 652-407
 (1)  
Begin the fuel transfer operation:

 (a)  
Make sure there is enough fuel capacity available in the inboard main tanks to permit fuel transfer from the reserve tanks.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 3(120)