54-62-03
 ALL  ú ú 02 Page 503 ú Oct 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SKIRT BEAM
WING

INBOARD STRUT

Trailing Edge Fairing Door - Fair Tolerances
Figure 502 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 54-62-03
 ALL  ú ú 02 Page 504 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

(REF)

E-E F-F Trailing Edge Fairing Door - Fair Tolerances Figure 502 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 54-62-03
 ALL  ú ú 02 Page 505 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

OUTBOARD STRUT:
CONSTANT TAPER - 0.66 INCH (16.5 mm) GAP AT LOWER FORWARD CORNER OF TRAILING EDGE FAIRING DOOR; 0.06 INCH (1.5 mm) GAP AT UPPER FORWARD CORNER OF TRAILING EDGE FAIRING DOOR. |0.04 INCH (|1.0 mm) TOLERANCE ALONG CONSTANT TAPER.
INBOARD STRUT:
CONSTANT TAPER - 0.46 INCH (11.5 mm) GAP AT LOWER FORWARD CORNER OF TRAILING EDGE FAIRING DOOR; 0.06 INCH (1.5 mm) GAP AT UPPER FORWARD CORNER OF TRAILING EDGE FAIRING DOOR. |0.04 INCH (|1.0 mm) TOLERANCE ALONG CONSTANT TAPER.

ON ALL EXCEPT NWA 007,008 OUTBOARD STRUTS, +0.060/-0.080 INCH (+1.52/-2.03 mm) FOR MAXIMUM 25% OF INTERFACE LENGTH +0.045/-0.055 INCH (+1.14/-1.40 mm) FOR MAXIMUM 25% OF INTERFACE LENGTH +0.025/-0.035 INCH (+0.64/-0.89 mm) FOR MAXIMUM 50% OF INTERFACE LENGTH
ON NWA 007 OUTBOARD STRUTS, +0.140/-0.080 INCH (+3.56/-2.03 mm) FOR MAXIMUM 25% OF INTERFACE LENGTH +0.045/-0.055 INCH (+1.14/-1.40 mm) FOR MAXIMUM 25% OF INTERFACE LENGTH +0.025/-0.035 INCH (+0.64/-0.89 mm) FOR MAXIMUM 50% OF INTERFACE LENGTH
ON NWA 008 OUTBOARD STRUTS, +0.060/-0.080 INCH (+1.52/-2.03 mm) FOR MAXIMUM 60% OF INTERFACE LENGTH +0.045/-0.055 INCH (+1.14/-1.40 mm) FOR MAXIMUM 25% OF INTERFACE LENGTH +0.025/-0.035 INCH (+0.64/-0.89 mm) FOR MAXIMUM 15% OF INTERFACE LENGTH

RIGHT AND LEFT SIDE DOORS:
|0.08 INCH (|2.0 mm) FOR MAXIMUM 30% OF INTERFACE LENGTH (UP TO 30% TO
FALL IN AFT 70% OF INTERFACE)
|0.06 INCH (|1.5 mm) FOR MINIMUM 70% OF INTERFACE LENGTH

|0.07 INCH (|1.8 mm) FOR MAXIMUM 30% OF INTERFACE LENGTH
|0.01 INCH (|0.3 mm) FOR MINIMUM 70% OF INTERFACE LENGTH

OUTBOARD STRUT:
CONSTANT TAPER - 0.50 INCH (12.7 mm) GAP AT UPPER FORWARD CORNER OF TRAILING EDGE FAIRING DOOR; 0.20 INCH (5.1 mm) GAP AT UPPER AFT CORNER OF TRAILING EDGE FAIRING DOOR. |0.04 INCH (|1.0 mm) TOLERANCE ALONG CONSTANT TAPER.
INBOARD STRUT:
0.20 |0.04 INCH (5.1 |1.0 mm) GAP

OUTBOARD STRUT: ON ALL EXCEPT NWA 008, +0.025/-0.100 INCH (+0.64/-2.54 mm) FOR 100% OF INTERFACE LENGTH
ON NWA 008, +0.05/-0.100 INCH (+1.27/-2.54 mm) FOR 30% OF INTERFACE LENGTH +0.025/-0.100 INCH (+0.64/-2.54 mm) FOR 70% OF INTERFACE LENGTH
INBOARD STRUT: +0.025/-0.100 INCH (+0.64/-2.54 mm) FOR MAXIMUM 35% OF INTERFACE LENGTH +0.025/-0.070 INCH (+0.64/-1.78 mm) FOR MINIMUM 65% OF INTERFACE LENGTH
____POSITIVE AND NEGATIVE SIGNS ON ALL INTERFACE DIMENSIONS REFER TO DIRECTION OF
NOTE: AIRFLOW RELATIVE TO INTERFACE:
AIRFLOW

AIRFLOW

(+) POSITIVE STEP  (-) NEGATIVE STEP
Trailing Edge Fairing Door - Fair Tolerances
Figure 502 (Sheet 3)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 54-62-03
 ALL  ú ú 03 Page 506 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 825-006
 (5)  Use Fig. 502 to do a check of the fair tolerances. (a) If necessary, adjust the door as follows: 1) Add or remove shims between the hinge brackets and the T/E door.
 2)  Add or remove shims between the shear fittings and the door, or between the shear fitting and the latch fitting.
 S 035-007
 (6)  On the outboard strut doors, remove all the shear fittings from the left side of the door except at the No. 2 latch.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 NACELLES/PYLONS(100)