S 544-005-N00

 (5)  
Use the heat gun to apply heat to the control switch to disconnect the wire leads from the control switch.

 TASK 78-34-06-404-006-N00
 3. Install the Thrust Reverser Control Switch
__________________________________________
 A. Equipment
 (1)  
4MIT65B80307-1 - Bubble Protractor

 (2)  
G76002-1 - Adapter, Protractor, Reverse Thrust Lever

 (3)  
Soldering Tool (to attach lead wires to switch)

 B.
References

 (1)  
AMM 27-62-00 201, Speed Brake Control System

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 78-34-06
 ALL  ú ú N01 Page 402 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
THRUST LEVERS
SEE B
SEE A
A
THRUST REVERSER
CONTROL SWITCH

THRUST REVERSER CONTROL SWITCH
THRUST LEVER 1  THRUST LEVER 2
B B
THRUST REVERSER
CONTROL SWITCH

THRUST REVERSER CONTROL SWITCH
THRUST LEVER 4THRUST LEVER 3
BB
Thrust Lever Switch Installation Figure 401
E12715
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 78-34-06
 ALL  ú ú N02 Page 403 ú Jun 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(2)  
AMM 76-11-03/201, Control Stand

 (3)  
AMM 76-11-01/501, Thrust Lever Assembly

 (4)  
IPC 76-11-01, Fig. 2

 C.
Access

 (1)  
Location Zone
 221 Control Cabin, LH
 222 Control Cabin, RH

 D.
Install the Control Switch for the Thrust Reverser (Fig. 401).

 S 314-008-N00
 (1)  
Use a soldering tool and solder to attach the wire leads to the control switch terminals.

 S 424-006-N00

 (2)  
Install the heat shrink sleeving over the exposed wire and terminal.

 S 424-009-N00

 (3)  
Install the applicable control switch with two screws on the mounting bracket of the applicable thrust lever as follows:

 NOTE: Do not fully tighten the screws at this time.
____
 (a)  
Thrust lever one - control switch S101

 (b)  
Thrust lever two - control switch S102

 (c)  
Thrust lever three - control switch S103

 (d)  
Thrust lever four - control switch S104

 S 864-010-N00
 (4)  
Make sure the forward thrust levers are in the idle position.

 S 484-011-N00

 (5)  
Attach the protractor adapter and the bubble protractor to the applicable reverse thrust lever.

 S 824-012-N00

 (6)  
Adjust the switch:

 (a)  
Move the switch on the mounting screws.

 (b)  
Partly tighten the two screws to hold the switch in place.

 (c)  
AIRPLANES PRE-SB 747-27A2356; Make sure the switch engages between 2 and 8 degrees of reverse thrust lever travel from the idle stow position.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 78-34-06
 ALL  ú ú N02 Page 404 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(d)  
AIRPLANES POST-SB 747-27A2356; Make sure the switch engages between 10 and 14 degrees of reverse thrust lever travel from the idle stow position.

 (e)  
If the switch does not engage at the correct angle, repeat the above steps. If repeated attempts fail to properly position the switch, adjust the switch by doing the following: 1) Remove the two screws and the switch from the thrust lever. 2) Bend the switch actuator arm to adjust the switch.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 EXHAUST 2(80)