NOTE: If voltage is less than 16 volts, the circuit may not
____ give sufficient current to fire the squib.
 S 865-118
 (21) Open this circuit breaker on the P6 panel:
 (a)  6H2, FIRE EXTINGUISHING ENG L BTL 2
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-21-00
 ALL  ú ú 15 Page 508 ú Sep 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

 S 765-138
 (22)
 Make sure the BOTTLE DISCHARGE light on the squib circuit test box goes off.

 S 765-137

 (23)
 Make sure the multimeter on the squib circuit test box shows 0 |2 volts.

 S 865-136

 (24)
 Close this circuit breaker on the P6 panel:

 (a)  6H2, FIRE EXTINGUISHING ENG L BTL 2
 S 215-157
 (25)
 Make sure the BOTTLE DISCHARGE light on the squib circuit test box comes on.

 S 215-158

 (26)
 Make sure the multimeter on the squib circuit test box shows 16 volts minimum.

 NOTE: If voltage is less than 16 volts, the circuit may not give
____
 sufficient current to fire the squib.

 S 745-135
 (27) Release the LEFT engine fire handle.
 (a)  
Make sure the fire handle moves quickly toward center about 10 degrees.

 (b)  
Make sure the BOTTLE DISCHARGE light on the squib circuit test box goes off.

 (c)  
Make sure the multimeter on the squib circuit test box shows 0 |2 volts.

 S 865-134
 (28) Put the LEFT engine fire handle to the usual (vertical) position.
 (a)  Make sure the EICAS message, L ENG SHUTDOWN, does not show on the top display.
 S 865-132
 (29)
 Set the LOAD CHECK switch on the squib circuit test box to the OFF position.

 S 025-131

 (30)
 Disconnect the bottle 2 left engine squib connector, D2268, from the squib circuit test box adapter cable.

 S 425-130

 (31)
 Connect the bottle 1 right engine squib connector, D2190, to the squib circuit test box adapter cable.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-21-00
 ALL  ú ú 16 Page 509 ú Sep 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 S 865-129
 (32)
 Set the LOAD CHECK switch on the squib circuit test box to the ON position.

 S 865-128

 (33)
 On the ENGINE FIRE Control Panel, P8, pull the RIGHT engine fire handle out to the emergency fire position.

 NOTE: When you pull the fire handles into the emergency fire
____ position, it is necessary to use the manual fire override switch behind the fire handle. When you turn the fire handles, it is necessary to hold the handles against the stops during the voltage measure.
 (a)  
Make sure the EICAS message, R ENG SHUTDOWN, shows on the top display.

 (b)  
Make sure the BOTTLE DISCHARGE light on the squib circuit test box stays off.

 (c)  
Make sure the multimeter on the squib circuit test box shows 0 |2 volts.

 S 865-144
 (34) Turn and hold the RIGHT engine fire handle fully counterclockwise to the DISCH 1 position.
 (a)  
Make sure the BOTTLE DISCHARGE light on the squib circuit test box comes on.

 (b)  
Make sure the multimeter on the squib circuit test box shows 16 volts minimum.

 NOTE: If voltage is less than 16 volts, the circuit may not
____ give sufficient current to fire the squib.
 S 865-222
 (35) Open this circuit breaker on the P6 panel:
 (a)  6H3, FIRE EXTINGUISHING ENG R BTL 1
 S 765-141
 (36)
 Make sure the BOTTLE DISCHARGE light on the squib circuit test box goes off.

 (37)
 Make sure the multimeter on squib circuit test box shows 0 |2 volts.

 S 865-139

 (38)
 Close this circuit breaker on the P6 panel: