(a)  6H4, FIRE EXTINGUISHING ENG R BTL 2
 S 216-043
 (52)
 Make sure the BOTTLE DISCHARGE light on the squib test box comes on.

 S 216-044

 (53)
 Make sure the multimeter on the squib test box shows 16 volts minimum.

 NOTE: If voltage is less than 16 volts, the circuit may not give
____
 sufficient current to fire the squib.

 S 986-125
 (54) Release the RIGHT engine fire handle.
 (a)  
Make sure the fire handle moves quickly toward center about 10 degrees.

 (b)  
Make sure the BOTTLE DISCHARGE light on the squib test box goes off.

 (c)  
Make sure the multimeter on the squib test box shows 0 |2 volts.

 S 866-126
 (55) Put the RIGHT engine fire handle to the usual (vertical) position.
 (a)  Make sure the EICAS message, R ENG SHUTDOWN, does not show on the top display.
 S 866-127
 (56)
 Set the LOAD CHECK switch on the squib test box to the OFF position.

 S 026-128

 (57)
 Disconnect the bottle 2 right engine squib connector, D2266, from the squib test box adapter cable.

 G. Squib Electrical Connection Procedure
 NOTE: Do this procedure each time you connect an electrical connector to
____
 a fire bottle squib.

 S 436-054
 (1)  Do the steps that follow to connect an electrical connector to a fire bottle squib.
 (a) Remove the protective cover from the fire bottle squib.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-21-03
 ALL  ú ú 03 Page 610 ú Sep 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 WARNING: MAKE SURE THERE IS NO VOLTAGE AT THE ELECTRICAL CONNECTOR.
_______ IF THERE IS A VOLTAGE AT THE ELECTRICAL CONNECTOR, THE SQUIB CAN RELEASE ITS CONTENTS SUDDENLY AND CAUSE INJURY TO PERSONS.
 (b)  Make sure there is no voltage between pins 1 and 2 of the electrical connector.
 NOTE: Connect a 10k ohm resistor across the meter to
____ remove any stray voltage from the electrical connector.
 (c)  Do the steps that follow to make sure you did not bend or damage the squib pins.
 NOTE: This step is necessary because the pins are most likely
____ to be damaged the first time an electrical connector is connected to the squib.
 1) Disconnect the electrical connector from the fire bottle
 squib. 2) Make sure the squib pins are not bent or damaged. 3) Make sure the electrical connector is not damaged.
 NOTE: The squib pins can cause damage to the connector if
____ the pins do not enter the electrical connector receptacles.
 4) Connect the electrical connector to the fire bottle squib.
 H. Connect the Squib Connectors
 S 866-129
 (1)  Open these circuit breakers on the P6 panel and attach DO-NOT-CLOSE tags:
 (a)  6H1, FIRE EXTINGUISHING ENG L BTL 1
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-21-03
 ALL  ú ú 01 Page 611 ú Sep 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 (b) (c) (d)  6H2, FIRE EXTINGUISHING ENG L BTL 26H3, FIRE EXTINGUISHING ENG R BTL 16H4, FIRE EXTINGUISHING ENG R BTL 2
 (2)  S 866-130Make sure these circuit breakers on the P11 panel are closed: (a) 11A32, IND LTS CKT 1 (b) 11A33, IND LTS CKT 2
 (3)  S 436-053Do the Squib Electrical Connection procedure to connect the squib electrical connector, D2188, to the left squib of bottle 1.
 (4)  S 866-131Remove the DO-NOT-CLOSE tag and close this circuit breaker on the P6 panel: (a) 6H1, FIRE EXTINGUISHING ENG L BTL 1
 (5)  S 986-132On the SQUIB TEST Control Panel, P61, push and hold the TEST switch. (a) Make sure the green L ENG 1 squib test light on the SQUIB TEST Control Panel, P61, comes on. (b) Make sure the R ENG 1, L ENG 2, and R ENG 2 squib test lights stay off.
 (6)  S 986-134Release the TEST switch. (a) Make sure the L ENG 1 squib test light goes off.
 (7)  S 866-136Make sure this circuit breaker on the P6 panel is open: (a) 6H3, FIRE EXTINGUISHING ENG R BTL 1
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 防火 FIRE PROTECTION 2(33)