S 825-037
(14)
Do the steps to adjust the left door on the right door to adjust the right door.
S 865-038
(15)
Remove the DO-NOT-OPERATE tag.
S 845-054
(16)
Move the control lever to DN to open the forward door.
S 845-055
(17)
Put the control lever to OFF.
32-22-00
ALL ú ú 05 Page 512 ú Jan 28/01
A
757
MAINTENANCE MANUAL
S 865-039
(18)
Remove the pressure from the left hydraulic system (AMM 29-11-00/201).
S 645-040
(19)
Apply grease to and install the parts that follow to connect the operating rods for the doors to the bellcrank:
(a)
Bolt (45)
(b)
Bushings (44)
(c)
Washer (43)
(d)
Nut (42)
(e)
Cotter Pin (41)
S 865-041
(20)
Pressurize the left hydraulic system (AMM 29-11-00/201).
S 865-042
(21)
Move the control lever to UP to close the forward doors.
S 845-056
(22)
Attach a DO-NOT-OPERATE tag.
S 225-043
(23)
make sure the doors and structures (Fig. 501, Views B-B, C-C, D-D) have the correct clearances and tolerances shown (Fig. 503, Views A-A, B-B, C-C, D-D, E-E, F-F, G-G, H-H).
S 845-109
(24)
If you removed or adjusted the aft doors or the aft door mechanisms, then do the steps that follow:
(a)
Put the contour template (28) at the forward edge of the aft door (4).
(b)
Make sure there is not more than 0.03 inch between the fit for the aft door and the contour template.
NOTE: If there is less than 0.03 inches between the aft door
____ and the template, adjust the forward hinge of the aft door (Fig. 501, View C-C).
32-22-00
ALL ú ú 09 Page 513 ú Sep 28/01
A
757
MAINTENANCE MANUAL
S 865-088
WARNING:_______ MAKE SURE THERE ARE NO PERSONS OR EQUIPMENT AROUND THE NOSE
LANDING GEAR BEFORE YOU MOVE THE CONTROL LEVER FOR THE LANDING
GEAR. THE NOSE LANDING GEAR CAN MOVE AND CAN CAUSE INJURY TO
PERSONS OR DAMAGE TO EQUIPMENT.
(25)
Remove the DO-NOT-OPERATE tag from the control lever for the landing gear.
S 865-006
(26)
Move the control lever for the landing gear to DN.
S 495-044
(27)
Install the downlock on the nose landing gear (AMM 32-00-20/201).
S 495-090
WARNING:_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(28)
Open the doors for the nose landing gear and install the door locks (AMM 32-00-15/201).
S 035-046
(29)
Remove the bolts (35) to disconnect the operating rods (32, 34) for the forward door from the door hinges.
S 845-047
(30)
Close the left forward door manually.
S 225-048
(31)
Measure the clearance between the alignment fitting (29) for the aft door (40) (Fig. 503, View D-D).
S 225-049
(32)
Do the steps again to measure the clearances and tolerances for the alignment fitting and the right forward door.
S 645-007
(33)
Apply grease to the parts and install them to connect the operating rods for the forward door (32, 34) to the forward door hinge (50):
(a)
Bolts (35)
(b)
Bushings (36)
(c)
Washers (37)
