E.
Install the Aft Door
S 414-011
(1)
Install these parts to connect the hinge for the forward door to the wall of the wheel well (Detail A):
(a)
Bolt (14)
(b)
Washer (15)
(c)
Nut (16)
(d)
Cotter Pin
S 414-012
(2)
Install these parts to connect the hinge for the aft door to the wall of the wheel well:
(a)
Bolt (9)
(b)
Bushing (10)
(c)
Washer (11)
(d)
Nut (12)
(e)
Cotter Pin
S 414-013
(3)
Install these parts to connect the operating rod for the door to the hinge of the forward door:
(a)
Bushing (2)
(b)
Bolt (1)
(c)
Washer (3)
32-22-03
ALL ú ú 01 Page 404 ú Mar 20/90
A
757 MAINTENANCE MANUAL
(d)
Nut (4)
(e)
Cotter Pin
S 414-016
(4)
Install these parts to connect the bonding jumpers to the door hinges:
(a)
Bolts (5)
(b)
Washers (6)
(c)
Spacers (7)
(d)
Nuts (8)
F.
Put the Airplane Back to Its Usual Condition
S 824-008
(1)
Make sure the aft door is adjusted correctly (Ref 32-22-00).
S 824-021
(2)
Make sure the aft door is adjusted correctly (AMM 32-22-00/501).
NOTE: Adjustment of the aft doors is not necessary if the same
____ doors, attaching hardware and adjustment rods that were removed are reinstalled and the jamnuts on the adjustment rods are not loosened.
S 644-009
(3) Lubricate the aft door at the grease fittings.
S 094-015
ú WARNING:_______USE THE PROCEDURE IN AMM 32-00-15 TO REMOVE THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(4) Remove the door locks for the landing gear and close the doors (Ref 32-00-15).
32-22-03
ALL ú ú 01.1 Page 405 ú Sep 28/02
A
1.
2.
ú
ú
ú
757 MAINTENANCE MANUAL
NOSE GEAR AFT DOOR OPERATING MECHANISM - REMOVAL/INSTALLATION
_____________________________________________________________
General
_______
A. This procedure contains the two tasks that follow:
(1)
The first task removes the operating mechanism for the aft door of the nose landing gear. It contains steps to disconnect the operating rods from the door hinge and the shock strut and remove the bellcrank. This task also contains steps to disconnect the operating rods from the bellcrank and remove the rods individually.
(2)
The second task installs the operating mechanism or the operating rods on the bellcrank for the aft door of the nose landing gear.
TASK 32-22-05-004-001Remove the Operating Mechanism for the Aft Door of the Nose Landing Gear
________________________________________________________________________ (Fig. 401)
A. References
(1)
32-00-15/201, Landing Gear Door Locks
(2)
32-00-20/201, Landing Gear Downlocks
B.
Access
(1)
Location Zones
711 Nose Landing Gear (NLG)
713/714 Forward NLG Doors
715/716 Aft NLG Doors
730/740 Main Landing Gear and Doors
C.
Prepare for the Removal of the Operating Mechanism
S 494-002
(1) Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
S 494-012
WARNING:_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. THE DOORSOPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSEINJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(2) Open the doors for the landing gear and install the door locks (AMM 32-00-15/201).
32-22-05
ALL ú ú 01.1 Page 401 ú Sep 28/02
A
757
MAINTENANCE MANUAL
BOLT BUSHING WASHER NUT
BELLCRANK
A
OPERATING RODS A FOR THE DOOR 30.01 INCHES
2
20.71
SEE A INCHES
2
BOLT BUSHING WASHER NUT
BOLT BUSHING WASHER NUT SHOCK STRUTAFT DOOR
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 2(28)
