(d)  
Pressurize the left hydraulic system (AMM 29-11-00/201).

 (e)  
Move the landing gear control lever from OFF to DN.

 (f)  
Make sure the rod end extends when the landing gear control lever is moved.

 (g)  
Examine the actuator for hydraulic leaks.

 S 864-022
 (7)  
Remove the pressure from the left hydraulic system and the hydraulic reservoir (AMM 29-11-00/201).

 S 034-014

 (8)  
Open the actuator bleed plug.

 S 984-015

 (9)  
Manually retract the rod end so that it is possible to connect it to the truck beam.

 S 644-016

 (10)
 Put grease on pin (1).

 S 434-017

 (11)
 Install the pin (1), antirotation bolt (4), collar (5), washers (2 and 6), nut (7), and cotter pin to connect the rod end of the actuator to the truck beam (View A-A).

 (12)
 Close the actuator bleed plug.

 S 434-018
 (a)  Install the bleed plug
 (b)  Install lockwire
 (c)  Apply BMS5-95 sealant around the bleed plug.  Clean the area
 where you will apply the sealant.

 S 414-031
 (13)
 Do these steps to install the conduit to the J-1 junction box (Fig. 402):

 (a)  
Put the wires that you disconnected back into the J-1 junction box

 32-32-15
 ALL  ú ú 01 Page 408 ú Sep 28/00
 
A

757
MAINTENANCE MANUAL

 (b)  Put the conduit in the correct position on the truck and
 install the clamp that attaches it to the truck beam
 (c)  Install the conduit coupling nut at the junction box
 (d)  Remove the tags from the sensor wires and install the wires
 into the terminal block in the junction box
 NOTE:____ Use the pin insertion tool.
 (e)  Do The Test for the Truck Tilt Sensor of the Main Landing Gear
 with the deactuator tool (AMM 32-09-07/201)
 (f)  Use the bolts to install the cover on the J-1 junction box.

 S 864-019
 (14) Make sure the fluid in the hydraulic reservoirs is at the correct level. Fill if it is necessary (AMM 12-12-01/301).
 

 32-32-15
 ALL  ú ú 01 Page 409 ú Sep 28/00
 
A

757 MAINTENANCE MANUAL
 MAIN GEAR TRUCK POSITIONER ACTUATOR - INSPECTION/CHECK
______________________________________________________
 1.  General_______
 A.  This procedure only has illustrations and a wear limit table which show the data for wear limits. There are no procedures for access, removal, or installation of the parts. Refer to the Main Gear Truck Positioner Actuator - Removal/Installation for procedures to do these tasks.
 TASK 32-32-15-226-001
 2.  Main Landing Gear Truck Positioner Actuator Wear Limits (Fig. 601)_______________________________________________________
 A.  General
 (1)  This procedure only has illustrations and a wear limit table which show the data for wear limits. There are no procedures for access, removal, or installation of the parts. Refer to the Main Gear Truck Positioner Actuator - Removal/Installation for procedures to do these tasks.
 

 32-32-15
 ALL  ú ú 01 Page 601 ú Jan 28/01
 
A

757
MAINTENANCE MANUAL

SHOCK 
DRAG  STRUT 
STRUT 
TRUCK 
POSITIONER 
ACTUATOR 
B 
A  TRUCK 
2. BEARING/PIN  POSITIONER 
ACTUATOR 
B 
A  1. BUSHING/PIN  1. BUSHING/PIN 
TRUCK 
FWD  BEAM  COLLAR 

TRUCK 
5. BEARING/PIN  POSITIONER 
ACTUATOR 
3. SIDEPLAY 
TRUCK 
BEAM 
4. BUSHING/PIN  4. BUSHING/PIN  A-A 
COLLAR 

SHOCK STRUT 6. SIDEPLAY
B-B
Main Landing Gear Truck Positioner Actuator Wear Limits Figure 601 (Sheet 1)

 32-32-15
 ALL  ú ú 01 Page 602 ú Mar 20/90
 
A
757
MAINTENANCE MANUAL

INDEX NO.  PART NAME  DIM.  DESIGN LIMITS  WEAR LIMITS  REPLACE PART WORN  REPAIR WORN PART  REPAIR INSTR. 
DIAMETER  DIM. WEAR PERMITTED  MAX DIAM CLEAR-ANCE
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 2(61)