A. General
(1) This procedure only has illustrations and a wear limit table which show the data for wear limits. There are no procedures for access, removal, or installation of the parts. Refer to Nose Gear Retract Actuator - Removal/Installation for procedures to do these tasks.
32-34-01
ALL ú ú 01 Page 601 ú Jan 28/01
A
757
MAINTENANCE MANUAL
5. BEARING/PIN LANDING GEAR SHOCK STRUT
B-B
Nose Landing Gear Retract Actuator Wear Limits
32-34-01
ALL ú ú 01 Page 602 ú Jan 20/99
H82463
A
757
MAINTENANCE MANUAL
YOU CAN REPAIR THE PART; REFER TO THE COMPONENT MAINTENANCE MANUAL FOR THE INSTRUCTIONS
THE SUM OF THE MAX DIAM. CLEARANCE MUST NOT EXCEED 0.010.
THE SUM OF THE MAX DIAM. CLEARANCE MUST NOT EXCEED 0.010.
DESIGN LIMITS WEAR LIMITS REPLACE REPAIRDIAMETER PER-MAXINDEX REPAIRPART NAME DIM.
WORNWORNMITTED DIAMNO.
INSTRPARTPARTWEAR CLEAR-MIN MAX DIM. ANCE
BUSHING PIN ID OD 1.7490 1.7500 1.7475 1.7495 1.7450 1.7530 0.005 2 X X
BEARING PIN ID OD 1.7490 1.7500 1.7475 1.7495 1.7450 1.7525 0.0052 X X
BEARING HOUSING ID OD 2.7495 2.7530 2.7500 2.7545 2.7470 2.7565 0.0072 X X
BUSHING PIN IDOD 1.7490 1.7515 1.7480 1.7500 1.7450 1.7530 0.0053 X X
BEARING PIN ID OD 1.7490 1.7500 1.7480 1.7495 1.7450 1.7525 0.0053 X X
BEARING HOUSING ID OD 2.7495 2.7530 2.7500 2.7545 2.7470 2.7565 0.0073 X X
1
1
1
1
1
1
32-34-01
Nose Landing Gear Retract Actuator Wear Limits
Figure 601 (Sheet 2)
ALL ú ú 01 Page 603 ú Jan 28/00
H88046
A
757 MAINTENANCE MANUAL
NOSE GEAR LOCK ACTUATOR - REMOVAL/INSTALLATION
______________________________________________
1. General
_______
A. This procedure contains two tasks. The first task is for removal of the lock actuator for the nose landing gear. The second task is for installation of the lock actuator.
TASK 32-34-02-004-022
2. Remove the Lock Actuator for the Nose Landing Gear (Fig. 401)
__________________________________________________
A. References
(1)
AMM 29-11-00/201, Pressure/Depressurize Main Hydraulic System
(2)
AMM 32-00-15/201, Landing Gear Door Locks
(3)
AMM 32-00-20/201, Landing Gear Downlocks
B.
Access
(1)
Location Zones
115 Nose Landing Gear Wheel Well (Left)
116 Nose Landing Gear Wheel Well (Right)
711 Nose Landing Gear
C.
Prepare for Removal
S 494-001
(1) Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
S 494-002
WARNING: USE THE PROCEDURE IN AMM 32-00-15/201 TO INSTALL THE DOOR
_______ LOCKS. THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(2)
Open the doors for the landing gear and install the door locks (AMM 32-00-15/201).
S 864-004
(3)
Remove the pressure from the left hydraulic system and hydraulic reservoir (AMM 29-11-00/201).
32-34-02
ALL ú ú 01 Page 401 ú Sep 28/00
A
757
MAINTENANCE MANUAL
LOCK LINK
A-A
WHEEL WELL
Nose Landing Gear Lock Actuator Installation
Figure 401
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 2(81)
