国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽

  • 熱門標簽

當前位置: 主頁 > 航空資料 > 飛行資料 >

時間:2010-05-22 22:46來源:藍天飛行翻譯 作者:admin
曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

go-around thrust as the airplane rotates to the go-around attitude.
Note: An automatic go-around cannot be initiated after touchdown or if the
airplane is below 5 feet radio altitude for more than 2 seconds.
The GA pitch mode initially commands a go-around attitude and then transitions
to speed as the rate of climb increases. This speed is normally between command
speed and command speed + 25 knots. The GA roll mode maintains existing
ground track. Above 400 feet AGL, select a roll mode as appropriate.
October 31, 2004
767 Flight Crew Training Manual
Approach and Missed Approach
Copyright © The Boeing Company. See title page for details.
5.64 FCT 767 (TM)
The minimum altitude for flap retraction during a normal takeoff is not normally
applicable to a missed approach procedure. However, obstacles in the missed
approach flight path must be taken into consideration. During training, use 1,000
feet AGL to initiate acceleration for flap retraction, as during the takeoff
procedure.
Note: Selection of pitch and roll modes below 400 feet AGL does not change the
autopilot and flight director modes.
Note: When accomplishing a missed approach from a multi-autopilot approach,
initial selection of a roll mode, pitch mode, or when altitude capture occurs
above 400 feet AGL the autopilot reverts to single autopilot operation.
If initial maneuvering is required during the missed approach, accomplish the
missed approach procedure through gear up before initiating the turn. Delay
further flap retraction until initial maneuvering is complete and a safe altitude and
appropriate speed are attained.
Command speed should not be increased until a safe altitude or flap retraction
altitude is attained. Accelerate to flap retraction speed by repositioning the
command speed to the maneuvering speed for the desired flap setting. Retract
flaps on the normal flap/speed schedule. When the flaps are retracted and the
airspeed approaches maneuvering speed, select FLCH and ensure CLB thrust is
set. Verify the airplane levels off at selected altitude and proper speed is
maintained.
If VNAV is used during go-around, the FMC missed approach profile should
contain the appropriate holding speeds and altitudes. Speed intervention may be
used to further modify airspeed as desired. If VNAV ALT (as installed) is
displayed, a premature level off may occur and selection of FLCH may be
required to complete the climb to the missed approach altitude.
If a diversion to an alternate airport is required, delay use of VNAV until
appropriate FMC entries are completed.
Note: FMC speeds may not comply with speed/altitude restrictions when using
VNAV at low altitudes.
October 31, 2004
767 Flight Crew Training Manual
Approach and Missed Approach
Copyright © The Boeing Company. See title page for details.
FCT 767 (TM) 5.65
Go–Around and Missed Approach - One Engine Inoperative
The missed approach with an engine inoperative should be accomplished in the
same manner as a normal missed approach except use flaps 5 for the go-around
flap setting for a flaps 20 approach or use flaps 20 as the go-around flap setting for
a flaps 25 or 30 approach. After GA is engaged, the AFDS commands a speed that
is normally between command speed and command speed + 15 knots. If
accomplishing a manual go-around, the pilot must control yaw with rudder and
trim. Some rudder pedal pressure may be required even with full rudder trim.
Select maximum continuous thrust when flaps are retracted to the desired flap
setting.
For a multi-autopilot go-around, yaw is initially controlled by the autopilots. Be
prepared to immediately apply rudder input when selecting another roll mode,
pitch mode, or when altitude capture occurs above 400 feet AGL because the
autopilot reverts to single autopilot operation. The system reverts to normal
autopilot operation and automatic control of rudder is discontinued.
Engine Failure During Go–Around and Missed Approach
If an engine fails during go-around, perform normal Go-Around and Missed
Approach procedures. Verify maximum go-around thrust is set. Maintain flaps 20,
VREF 30 + wind correction (5 knots minimum) speed until initial maneuvering is
complete and a safe altitude is reached. Accelerate to flap retraction speed by
repositioning the command speed to the maneuvering speed for the desired flap
setting. Retract flaps on the normal flap/speed schedule.
October 31, 2004
767 Flight Crew Training Manual
Approach and Missed Approach
Copyright © The Boeing Company. See title page for details.
5.66 FCT 767 (TM)
Intentionally
Blank
October 31, 2004
 
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址:767機組訓練手冊Flight Crew Training Manual (FCTM)767(87)
国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽
午夜精品在线视频| 日本一欧美一欧美一亚洲视频| 欧美一区二区在线视频观看| 一本久道中文无码字幕av| 久久亚洲成人精品| 国产精品女人网站| 国产精品久久久久久久久久久久午夜片 | 国产美女网站在线观看| 日韩欧美在线免费观看视频| 亚洲 国产 日韩 综合一区| 91精品国产高清自在线| 久久久久久九九九| 欧美性一区二区三区| 午夜精品短视频| 欧洲精品亚洲精品| 欧美一级大胆视频| 男人天堂a在线| 99亚洲精品视频| 国产精品av在线| 久久久久久久久久久网站| 九一国产精品视频| 久久精品国产96久久久香蕉| 国产精品极品美女粉嫩高清在线| 久久久久久999| 日韩精品av一区二区三区| 国内精品一区二区三区| 99视频在线免费播放| 久久影视中文粉嫩av| 国产精品日韩欧美综合| 久久999免费视频| 在线观看一区欧美| 日本欧美精品在线| 免费看a级黄色片| www插插插无码免费视频网站| 国产av天堂无码一区二区三区| 国产精品久久久久9999小说| 亚洲精品日韩精品| 免费日韩中文字幕| 久久人妻精品白浆国产| 久久中文久久字幕| 欧洲美女7788成人免费视频| 日本一区二区三区四区高清视频| 国产一区二区不卡视频| 成人一区二区在线| 热久久视久久精品18亚洲精品| 欧洲国产精品| 久久精品91久久香蕉加勒比| 国产精品成人v| 亚洲色欲久久久综合网东京热| 茄子视频成人免费观看| 777久久精品一区二区三区无码 | 三年中文高清在线观看第6集| 最新中文字幕久久| 国内成+人亚洲| 国产av熟女一区二区三区| 亚洲 日韩 国产第一区| 粉嫩av一区二区三区免费观看 | 男女午夜激情视频| 精品国产一区二区三区在线观看 | 日本一区视频在线播放| 国产视频一区二区三区四区| 国产精品秘入口18禁麻豆免会员| 日韩精品一区二区三区不卡| 国产成人艳妇aa视频在线| 欧美一区二区三区免费视| 久久久女人电视剧免费播放下载| 五月婷婷综合色| 久久久久久久久久久久久国产| 日韩欧美视频一区二区三区四区| www.日日操| 三级网在线观看| 色阁综合伊人av| 黄页网站在线观看视频| 久久综合免费视频| 99久久久精品视频| 中文字幕一区二区三区有限公司 | 蜜桃91精品入口| 精品国产一区二区三区久久久久久 | 日本手机在线视频| 国产精品久久久久影院日本| 成人免费在线网址| 国产一区在线免费观看| 7777精品久久久久久| 国产福利片一区二区| 131美女爱做视频| 国产欧美精品久久久| 91精品国产高清久久久久久91| 国产精品久久久久久久久久久久| 久久久久久欧美| 国产福利久久| 91av免费看| 国产精品18久久久久久麻辣| 114国产精品久久免费观看| 国产在线精品一区| 8050国产精品久久久久久| 亚洲一区三区在线观看| 免费拍拍拍网站| 日韩中文娱乐网| 青草青草久热精品视频在线网站| 国产成人精品视频免费看| 秋霞无码一区二区| 欧美激情视频在线免费观看 欧美视频免费一| 韩国一区二区av| 亚洲精品国产一区| 欧美激情第1页| 久久久999成人| 欧美最猛性xxxx| 国产精品户外野外| 国产日韩av在线| 日韩精品最新在线观看| 一区二区三视频| 国产精品视频播放| www.亚洲成人| 国产一区二区三区播放| 亚洲美女搞黄| 日韩亚洲欧美中文在线| 俄罗斯精品一区二区| 国内伊人久久久久久网站视频| 色综合影院在线观看| 亚洲一区二区自拍| 国产99久久精品一区二区 夜夜躁日日躁| 不卡一区二区三区视频| 欧美自拍大量在线观看| 精品乱码一区二区三区| 国产激情综合五月久久| 99亚洲精品视频| av无码精品一区二区三区| 成人国产一区二区| 成人久久18免费网站漫画| 国产一区二区精品在线| 日韩不卡视频一区二区| 欧美日本中文字幕| 久久久久久久久久久久久久国产 | 天堂va久久久噜噜噜久久va| 中文网丁香综合网| 日韩免费av一区二区| 国产精品久久久久福利| 丰满少妇久久久| 国产九色91| 国产日韩一区二区在线| 精品一区二区三区视频日产| 欧日韩不卡在线视频| 欧美日韩精品免费观看视一区二区| 日韩欧美激情一区二区| 国内揄拍国内精品| 欧美少妇一区| 黄在线观看网站| www.久久草| 久久久久亚洲精品| 国产精品国产三级国产aⅴ浪潮 | 国产欧美在线看| av一区二区三区免费观看| 日韩在线视频网站| 色综合久久久888| 一本久道久久综合狠狠爱亚洲精品| 一本—道久久a久久精品蜜桃| 亚洲一区精品电影| 欧美日韩一区二区三区在线视频| 国内精品久久久久久| 久久这里只有精品18| 亚洲 日韩 国产第一| 日韩欧美激情一区二区| 国语自产精品视频在免费| 国产欧美精品久久久| 日日骚久久av| 日韩视频永久免费观看| 午夜精品久久久久久久久久久久久| 波多野结衣成人在线| 色偷偷888欧美精品久久久| 国产精品高潮呻吟久久av无限| 精品久久久久久一区二区里番 | 亚洲精品欧美日韩专区| 日本网站免费在线观看| 国产素人在线观看| 国产精品久久久久久久久久东京| 婷婷久久青草热一区二区| 精品少妇在线视频| 国产精品1区2区在线观看| 久久国产一区二区三区| 亚洲欧美丝袜| 成人精品小视频| 久久国产精品影片| 黄色网在线视频| 亚洲成人一区二区三区| 精品视频免费在线播放| 国产成人亚洲综合无码| 中文字幕不卡每日更新1区2区| 精品欧美日韩| 国产精品视频一| 激情视频在线观看一区二区三区| 深夜精品寂寞黄网站在线观看| 成人毛片100部免费看| 国产精品日韩欧美| 欧美日韩激情四射| 国产精品入口免费视频一| 欧美日韩一道本| 色偷偷噜噜噜亚洲男人| 极品粉嫩国产18尤物| 韩国精品久久久999| 成人精品一二区|