曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Displays traffic information on Navigation Map
Displays topographical data (e.g., coastlines, terrain, rivers, lakes) and
elevation scale on Navigation Map
Displays terrain information on Navigation Map
AIRWAYS: Displays airways on the map when next level softkeys are pressed
(default label is dependent on map setup option selected); cycles through the following:
AIRWY ON: All airways are displayed
AIRWY LN: Only low-altitude airways are displayed
AIRWY HI: Only high-altitude airways are displayed
Displays NEXRAD weather and coverage information on Navigation
Map (optional feature)
Displays XM lightning information on Navigation Map (optional feature)
Returns to top-level softkeys
Selects desired amount of map detail; cycles through declutter levels:
DCLTR (No Declutter): All map features visible
DCLTR-1: Declutters land data
DCLTR-2: Declutters land and SUA data
DCLTR-3: Removes everything except for the active flight plan
When available, displays optional airport and terminal procedure charts
When available, displays optional checklists
Table 16-6. MFD SOFTKEYS
# CONTROL DESCRIPTION
1 Dual FMS Knob Flight management system knob. This knob selects the MFD page to be viewed; the large knob
selects a page group (MAP, WPT, AUX, NRST), while the small knob selects a specific page within the
page group. Pressing the FMS Knob turns the selection cursor ON and OFF. When the cursor is ON,
data may be entered in the applicable window by turning the small and large knobs. In this case, the
large knob moves the cursor on the page, while the small knob selects individual characters for the
highlighted cursor location.
2 Direct-to Key Allows the user to enter a destination waypoint and establish a direct course to the selected
destination (the destination is either specified by the identifier, chosen from the active route, or taken
from the map pointer position).
3 FPL Key Displays the active flight plan page for creating and editing the active flight plan, or for accessing
stored flight plans.
4 MENU Key Displays a context-sensitive list of options. This list allows the user to access additional features or
make setting changes that relate to particular pages.
5 PROC Key Gives access to IFR departure procedures (DPs), arrival procedures (STARs) and approach
procedures (IAPs) for a flight plan. If a flight plan is used, available procedures for the departure
and/or arrival airport are automatically suggested. These procedures can then be loaded into the
active flight plan. If a flight plan is not used, both the desired airport and the desired procedure
may be selected.
6 Joystick Changes the map range when rotated. Activates the map pointer when pressed. Pans the map or
cursor when moved.
7 Alphanumeric Keys Allow entry of airports, waypoints, etc.
8 Plus (+) Minus (-) Key Toggles a (+) or (-) character.
9 Decimal Key Enters a decimal point.
10 SEL Key The center of this key activates the selected softkey, while the right and left arrows move the softkey
selection box to the right and left, respectively.
11 ENT Key Validates or confirms a menu selection or data entry.
12 CLR Key Erases information, cancels entries, or removes page menus. Pressing and holding this key displays
the navigation map page.
13 SPC Key Adds a space character.
14 BKSP Key Moves the cursor back one character space.
Table 16-7. MFD CONTROLLER DESCRIPTIONS
510OM-00 16-31
CITATION MUSTANG OPERATING MANUAL
ENGINE INDICATING AND
CREW ALERTING SYSTEM
The left side of the MFD displays the two-column
EICAS display. The EICAS display includes
the engine indicating system (EIS) and
the CAS.
Engine Indicating System
The EIS is a group of graphical and digital indications
of the condition and performance of
the aircraft system. These include indications for:
• Engines and oil system
• Fuel system
• Electrical system
• Pressurization
• Rudder and aileron trim
• Flap position
Crew Alerting System
The CAS is described in detail in Chapter 4—
“Master Warning,” along with a summary explanation
of each CAS message.
MAIN MFD DISPLAY AREA
The main MFD area presents different pages
from four main page groups:
• MAP—Moving-map displays
• WPT—Waypoint information pages
• AUX—Auxiliary information pages
• NRST—Nearest facilities
The selected display page group is noted by
a cyan abbreviation (MAP, WPT, AUX, or
NRST) in the lower right corner of the main
display area. Each page group contains more
than one page, indicated by the group of
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Cessna塞斯納公務機飛行手冊(111)