____
 (10)
 Install the sense line connectors (4), (5), (12) and (14). NOTE : Apply a small quantity of COMMON GREASE (Material No. 04-014A)

____
 to the threaded parts of the connectors.

 (11)
 TORQUE the sense line connectors (4), (5), (12) and (14) to between

 0.9 and 0.915 m.daN (79.64 and 80.97 lbf.in).

 (12)
 Install the pneumatic sense hose (16).

 (13)
 TORQUE the pneumatic sense hose (16) connector to between 0.95 and

 1.05 m.daN (84.07 and 92.92 lbf.in).

 (14)
 Make sure that the clamps (6) and (10) are in the correct position.

 (15)
 TORQUE the clamps (6) and (10) to between 0.51 and 0.56 m.daN (45.13 and 49.55 lbf.in).

 (16)
 Put the bonding strap (13) in position on the reheater (18) and install the screw (9), the washer (17) and the nut (15).

 (17)
 TORQUE the nut (15) to between 0.2 and 0.25 m.daN (17.69 and 22.12 lbf.in) (Ref. TASK 20-28-00-912-004).

 (18)
 Remove the blanking caps and connect the electrical connector (3).

 (19)
 Make sure that the work area is clean and clear of tool(s) and other items.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 21-61-41Page 415 1201-299, 1Aug 01/05 1 1 1CES 1R **ON A/C 301-399,

 Subtask 21-61-41-420-050-A
 A. Installation of the Anti-ice Valve
 (1)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (2)
 Make sure that the anti-ice valve sense-lines are in a good condition (Ref. TASK 21-52-00-200-003).

 (3)
 Make sure that the removed packings are in a good condition. If necessary replace the packing (2) and/or the packing (7).

 (4)
 Remove the blanking plugs from the disconnected line ends.

 (5)
 Clean the component interface and/or the adjacent area.

 (6)
 Apply lubricant: CAUTION : USE ONLY THE SPECIFIED LUBRICANT TO LUBRICATE THE O-RINGS

_______ AND THE PACKINGS. OTHER LUBRICANTS CAN CAUSE SMOKE OR A SMELL IN THE CABIN WHEN THEY BECOME HOT.
 (a) Apply a small quantity of LUBRICANTS (Material No. 06-007) to the packings (2) and/or (7).
 (7)
 Put the packing (2) in position on the anti-ice valve (13) and the packing (7) in position on the pipe-assembly flange (8).

 (8)
 Put the anti-ice valve (13) in position between the pipe-assembly flange (1) and the pipe-assembly flange (8).

 (9)
 Install the clamps (6) and (12).
 NOTE : Do not fully tighten at this time.

____
 (10)
 Install the sense line connectors (4), (5), (14) and (18). NOTE : Apply a small quantity of COMMON GREASE (Material No. 04-014A)

____ to the threaded parts of the connectors.

 (11)
 TORQUE the sense line connectors (4), (5), (14) and (18) to between

 0.9 and 0.915 m.daN (79.64 and 80.97 lbf.in).
R 1EFF : 301-399, 1 21-61-41Page 416 1 1 Aug 01/05 1 1 1CES 1

 (12) Install the pneumatic sense hose (9).
 (13) TORQUE the pneumatic sense hose (9) connector to between 0.95 and 1.05 m.daN (84.07 and 92.92 lbf.in).
 (14) Make sure that the clamps (6) and (12) are in the correct position.
 (15) TORQUE the clamps (6) and (12) to between 0.51 and 0.56 m.daN (45.13 and 49.55 lbf.in).
 (16) Put the bonding strap (10) in position on the reheater (16) and install the screw (11), the washer (15) and the nut (17).
 (17) TORQUE the nut (17) to between 0.2 and 0.25 m.daN (17.69 and 22.12 lbf.in) (Ref. TASK 20-28-00-912-004).
 (18) Remove the blanking caps and connect the electrical connector (3).
 (19) Make sure that the work area is clean and clear of tool(s) and other items. 
R  **ON A/C 401-499, 
R  Subtask 21-61-41-420-050-B 
R  A. Installation of the Anti-ice Valve 
R R  (1) Make sure that the parts retained from the removed component are clean and in the correct condition. 
R R  (2) Make sure that the removed packings are in a good condition. If necessary replace the packing (2) and/or the packing (5). 
R  (3) Remove the blanking plugs from the disconnected line ends. 
R  (4) Clean the component interface and/or the adjacent area. 
R  (5) Apply lubricant: 
R R R  CAUTION : USE ONLY THE SPECIFIED LUBRICANT TO LUBRICATE THE O-RINGS_______ AND THE PACKINGS. OTHER LUBRICANTS CAN CAUSE SMOKE OR A SMELL IN THE CABIN WHEN THEY BECOME HOT. 
R R  (a) Apply a small quantity of LUBRICANTS (Material No. 06-007) to the packings (2) and (5). 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 5(45)