_
2 If necessary replace the seal (4).
_
a Remove the damaged seal (4).
_ b Clean the seal contact area of the ram-air outlet (6) with
_ CLEANING AGENTS (Material No. 11-003).
c Attach the new seal (4) to the ram-air outlet (6) with
_ BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004A).
(3) Put the ram-air outlet (6) in position and:
(a) For the left ram-air outlet, 1 Install the washers (5) and the bolts (13), (14), (16), (17)
_ and (19) as identified in the removal procedure.
NOTE : Do not tighten the bolts at this time.
____
(b) For the right ram-air outlet, 1 Install the washers (5) and the bolts (13), (15), (16), (18)
_ and (19) as identified in the removal procedure.
1EFF : 001-003, 051-054, 1 21-61-52Page 437 1 1 Aug 01/05R 1 1 1CES 1
NOTE : Do not tighten the bolts at this time.
____
(4)
Put the tie rod (12) in position and install the bolt (11), the washer (10) and the nut (9).
(5)
Install the washers (8) and the screws (7).
(6)
Put the clamp (2) and the sleeve (1) in position on the ram-air outlet (6).
(7)
Tighten the clamp (2).
(8)
Remove the blanking caps and connect the electrical connector (3).
(9)
Make sure that the work area is clean and clear of tool(s) and other items.
(10)
Install the access panel/s (Ref. TASK 53-35-13-400-002).
(a)
For the left ram-air outlet, 1 191KB.
_
(b)
For the right ram-air outlet,
(11)
Torque the bolts:
1_ 192KB.
NOTE : This will make sure that the ram-air outlet is in the____
correct position.
(a) For the left ram-air outlet: 1 the bolts (13), (17) and (19) to 0.36 m.daN (31.85 lbf.in),
_
2 the bolts (14) and (16) to 0.36 m.daN (31.85 lbf.in)
_
(Ref. TASK 20-28-00-912-004).
(b) For the right ram-air outlet: 1 the bolts (13), (18) and (19) to 0.36 m.daN (31.85 lbf.in),
_
2 the bolts (15) and (16) to 0.36 m.daN (31.85 lbf.in)
_
(Ref. TASK 20-28-00-912-004).
1EFF : 001-003, 051-054, 1 21-61-52Page 438 1 1 Aug 01/05R 1 1 1CES 1
(12) Remove the access panel/s (Ref. TASK 53-35-13-000-002).
(a) For the left ram-air outlet,
1 191KB.
_
(b) For the right ram-air outlet,
1 192KB.
_
(13) Make sure that the work area is clean and clear of tool(s) and other items.
R **ON A/C 004-049, 055-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 21-61-52-420-053-A
A. Installation of the Ram-Air Outlet
(Ref. Fig. 403A/TASK 21-61-52-991-007-A)
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(1)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(2)
Examine the seal:
(a) For the left ram-air outlet,
1 Make sure that the seal (3) is in a good condition.
_
2 If necessary replace the seal (3)
_
a Remove the damaged seal (3).
_
3 To Clean the Seal Contact Area and to Attach the Seal
_ WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
-clean the seal contact area of the ram-air outlet (5) with CLEANING AGENTS (Material No. 11-003).
-attach the new seal (3) to the ram-air outlet (5) with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004A).
(b) For the right ram-air outlet,
1 Make sure that the seal (3) is in a good condition.
_
2 If necessary replace the seal (3).
_
a Remove the damaged seal (3).
_ b Clean the seal contact area of the ram-air outlet (5) with
_ CLEANING AGENTS (Material No. 11-003).
c Attach the new seal (3) to the ram-air outlet (5) with
_ BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004A).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 5(83)
