-for item (4) (Ref. TASK 21-61-00-300-001).
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | CC | 9.983 | 9.992 | | | 9.976 | | | | OD 13 |(0.3930) |(0.3933) | | |(0.3927) | | | | | | | 0.008 | 0.035 | | | 0.049 | | | | | (0.0003)| (0.0013)| | |(0.0019)| | CC | 10.000 | 10.018 | | | | 10.025 | | | ID 4 |(0.3937) |(0.3944) | | | |(0.3946) | | ------------------------------------------------------------------------------- Subtask 21-61-51-220-059
J. In-Service Wear Limits
(1) Use applicable measurement equipment and measure the OD of the bolt
(14) and the ID of the shouldered bushing (5).
NOTE : If any of the components are 'out of limits' then you must
____
replace them.
-for item (5) (Ref. TASK 21-61-00-300-001).
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | CC | 6.325 | 6.337 | | | 6.318 | | | | OD 14 |(0.2490) |(0.2494) | | |(0.2487) | | | | | | | 0.003 | 0.027 | | | 0.041 | | | | | (0.0001)| (0.0010)| | |(0.0016)| | CC | 6.340 | 6.352 | | | | 6.359 | | | ID 5 |(0.2496) |(0.2500) | | | |(0.2503) | | -------------------------------------------------------------------------------
Subtask 21-61-51-220-060
K. In-Service Wear Limits
(1) Use applicable measurement equipment and measure the OD of the bolt
(7) and the ID of the shouldered bushing (4).
NOTE : If any of the components are 'out of limits' then you must
____
replace them.
-for item (4) (Ref. TASK 21-61-00-300-001).
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | DD | 7.905 | 7.925 | | | 7.898 | | | | OD 7 |(0.3112) |(0.3120) | | |(0.3109) | | | | | | | 0.005 | 0.036 | | | 0.050 | | | | | (0.0001)| (0.0014)| | |(0.0019)| | DD | 7.930 | 7.941 | | | | 7.948 | | | ID 4 |(0.3122) |(0.3126) | | | |(0.3129) | | -------------------------------------------------------------------------------
Subtask 21-61-51-220-061
L. In-Service Wear Limits
(1) Use applicable measurement equipment and measure the OD of the bolt
(7) and the ID of the bushing (8).
NOTE : If any of the components are 'out of limits' then you must
____
replace them.
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | DD | 7.905 | 7.925 | | | 7.898 | | | | OD 7 |(0.3112) |(0.3120) | | |(0.3109) | | | | | | | 0.005 | 0.036 | | | 0.050 | | | | | (0.0001)| (0.0014)| | |(0.0019)| | DD | 7.930 | 7.941 | | | | 7.948 | | | ID 8 |(0.3122) |(0.3126) | | | |(0.3129) | | ------------------------------------------------------------------------------- Subtask 21-61-51-220-062
中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM AIR CONDITIONING 空調(diào) 5(73)
