B. Do the test given in Para. 3.A.
 F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page B237
 E E Aug 01/05 E E ECES
E

 F  『
 E  C F M  E
 E  E

 E 56 E
 E E
 CONTROLLING - FAULT ISOLATION PROCEDURES

________________________________________
 TASK 73-20-81-810-801
 Loss of the PO Sensor Signal on Engine 1

 1. Possible Causes
_______________
 - ECU (4000KS)
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R  AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit R (ECU)(4000KS) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with Engine non Motoring)
 3. Fault Confirmation
__________________
 A. Do the operational test of the FADEC 1A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message ECU (P0 SENSOR):
 - make sure that the P0 nipple on the ECU (4000KS) is clear and not clogged.
 (1) If the fault continues:

 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 F 『 EEFF : ALL E ∞∞73-20-81∞∞∞∞∞∞∞∞∞∞Page 201
 E E May 01/99 E E ECES
E

 F 『
 E C F M E
 E E
 E 56 E
 E E

 TASK 73-20-81-810-802
 Loss of the PO Sensor Signal on Engine 2
 1. Possible Causes
_______________
 - ECU (4000KS)
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
R AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit R (ECU)(4000KS) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with Engine non Motoring)
 3. Fault Confirmation
__________________
 A. Do the operational test of the FADEC 2A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message ECU (P0 SENSOR):
 - make sure that the P0 nipple on the ECU (4000KS) is clear and not clogged.
 (1) If the fault continues:
 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 F 『 EEFF : ALL E ∞∞73-20-81∞∞∞∞∞∞∞∞∞∞Page 202
 E E May 01/99 E E ECES
E

 F 『
 E C F M E
 E E
 E 56 E
 E E

 TASK 73-20-81-810-803
 Internal Failure of the ECU on Engine 1
 1. Possible Causes
_______________
 - ECU (4000KS)
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
R AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit R (ECU)(4000KS) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with Engine non Motoring) ASM 73-25/10
 3. Fault Confirmation
__________________
 A. Do the operational test of the FADEC 1A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message ECU (ARINC OUT):
 - do a check for a short to ground at the wiring and connectors between the ECU (4000KS) and the test receptacle of the aircraft computers: . EIU1 (1KS1) - DMC1 (1WT1) . DMC2 (1WT2) - DMC3 (1WT3) . FMGC1 (1CA1) - FWC1 (1WW1) . FWC2 (1WW2) - DMU (1TV) (Ref. ASM 73-25/10).
 (1) If there is a short to ground:
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機燃油和控制 2(5)