A. Replace the CONT-ZONE TEMPERATURE (8HK) (Ref. AMM TASK 21-63-34-000-001) and (Ref. AMM TASK 21-63-34-400-001).
R (1) If the fault continues:
R - Do a check for open or short to ground of the between the EIU
R (1KS1) and harness J3 the ECU (4000KS) pins AB/5A, 5C to pins
R J3/22, 23 (Ref. ASM 732506)

R (a) If the wiring is not correct:
R - repair the above wiring.
R

R (b) If the wiring is correct:

 - Replace the EIU-2 (1KS2) (Ref. AMM TASK 73-25-34-000-040) and
 (Ref. AMM TASK 73-25-34-400-040). R
 F 『

 ∞∞73-25-00∞∞∞∞∞∞∞∞∞∞Page 268
EEFF :  ALL  E 
E  E  Aug 01/05
 E  E
 ECES  E

 F  『
 E  C F M  E
 E  E
 E  56  E
 E  E 

R (c) If the fault continues:
 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 B. No additionnal maintenance action is required if the fault is not confirmed.
 (1) Repeat the fault isolation procedure if the fault continues.
 F 『 EEFF : ALL E ∞∞73-25-00∞∞∞∞∞∞∞∞∞∞Page 269
 E E Aug 01/05 E E ECES
E TASK 73-25-00-810-895

 F  『
 E  C F M  E
 E  E
 E  56  E
 E  E

 Loss of Data on the ARINC Bus from the EIU to the FADEC on Engine 1
 1. Possible Causes_______________
 - EIU-1 (1KS1)

 - harness J3 from EIU-1 (1KS1) to ECU (4000KS)

 - ECU (4000KS)

 2. Job Set-up Information______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
AMM 73-21-60-000-001  Removal of the Electronic Control Unit (ECU)(4000KS)
 AMM 73-21-60-400-001  Installation of the Electronic Control Unit (ECU)(4000KS)
 AMM 73-25-34-000-040  Removal of the Engine Interface Unit (EIU) (1KS1,1KS2)
 AMM 73-25-34-400-040  Installation of the Engine Interface Unit (EIU) (1KS1,1KS2)
 AMM 73-29-00-710-040  Operational Test of the FADEC on the Ground (with Engine non Motoring)
 ASM 73-25/06
 3. Fault Confirmation__________________
 A. Test
 (1) Do the operational test of the FADEC 1A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
 4. Fault Isolation_______________
 A. If the test gives the maintenance message CFDIU, EIU (155), J3*:
 - do a check for open or short to ground at pins AB/5A, 5C to pins J3/22, 23 of the harness J3 from EIU-1 (1KS1) to ECU (4000KS) (Ref. ASM 73-25/06).
 (1) If the wiring is not correct:

 - repair the above harness J3.

 (2) If the wiring is correct:

 - replace the EIU-1 (1KS1) (Ref. AMM TASK 73-25-34-000-040) and (Ref. AMM TASK 73-25-34-400-040).
 F 『 EEFF : ALL E ∞∞73-25-00∞∞∞∞∞∞∞∞∞∞Page 270
 E E Aug 01/05 ERE
ECES  F 『 E C F M E E E E 56 E E E (3) If the fault continues:

 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 B. Do the test given in Para. 3.A.
 F 『 EEFF : ALL E ∞∞73-25-00∞∞∞∞∞∞∞∞∞∞Page 271
 E E Aug 01/05 ERE
ECES

 F 『
 E C F M E
 E E
 E 56 E
 E E

 TASK 73-25-00-810-896
 Loss of Data on the ARINC Bus from the EIU to the FADEC on Engine 2
 1. Possible Causes
_______________
 - EIU-2 (1KS2)

 - harness J3 from EIU-2 (1KS2) to ECU (4000KS)

 - ECU (4000KS)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU)(4000KS) AMM 73-25-34-000-040 Removal of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-25-34-400-040 Installation of the Engine Interface Unit (EIU) (1KS1,1KS2) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with Engine non Motoring) ASM 73-25/06
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機燃油和控制 2(57)