(g)  
Smooth filled area by wiping with soft cloth and MEK or by sanding with 400 to 600 grit abrasive paper and featheredges.

25-00-11  Feb 20/86
Page 248
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.

(h)  
Repeat (f) and (g) if necessary.

(i)  
Retexture surface as necessary, apply ink or paint with a 00 brush for scratch line retexturing or with a very flexible silicone blanket (with desired texture) for larger area repairing.

NOTE: Cover damaged area only as needed to blend-in repair area.

(j)  
Check surface to determine that repair will not show.

(k)  
If surface is unsatisfactory, repeat steps (a) thru (i) until repaired area does not show.

(l)  
When surface texture is satisfactory, lightly spray repair area as necessary.

(m)  
Feather spray to cover 1 to 2 inches on each side of damage. When repair is on a pattern texture surface, apply paints per AM.(4)(b).

(n)  
Match glass of repair to surrounding area. Reduce gloss by spraying with matte finish

as necessary. Increase gloss by spraying with clear acrylic as necessary. AM. Repair Method 39
(1)  General
(a)  This method is for repair of surface damage in Tedlar covered crushed core (per BAC5564)
NOTE:  This method is for scratches or minor indented (or gauged) surfaces. Indentations are not to exceed 0.01-inch depth for 0.03-inch thick Tedlar covered crushed core panels. Indentations are not to exceed 0.005-inch depth for 0.080-inch thick Tedlar crushed core panels.
(2)  
Equipment and Materials

(a)  Refer to AL.(2)

(3)  
Repair Procedure for Scratched Solid Color Surface

(a)  Proceed with repair procedures AL.(3)(a) thru AL.(3)(n).

(4)  
Repair procedures for Scratched Pattern Texture Surface

(a)  
Proceed with repair procedures AL.(3)(a) thru AL.(3)(e).

(b)  
Using a fine tip artist brush, paint ink base over repaired area.

NOTE:  It may be necessary for repair operator to rematch ink before applying or reapply necessary ink proportions until desired color is achieved.
505 
Feb 20/86  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  25-00-11 Page 249 

CABIN ACCOMMODATION CONVERSIONS - DESCRIPTION AND OPERATION
EFFECTIVITY
GJ B-2501 thru B-2505
1. General
A.  The interior furnishings and equipment in the main cabin of these airplanes are designed to allow easy and rapid convertibility between several configurations of accommodation for passengers and/or cargo.
B.  On Passenger/Cargo Convertible Airplanes, the main cabin can be cleared of passenger equipment and converted to accommodate cargo. Alternatively a fume-tight dividing partition may be installed across the cabin at five different positions: cargo is then accommodated forward of the partition and passengers aft.
C.  The types of accommodations available are:
(1)  
All-Passenger

(a) 
 124 Tourist

(b) 
 130 Tourist

(c)  
104 Tourist/8 First Class

(2)  
All-Cargo

(3) 
 Combined Passenger/Cargo

(a)  
2 pallets/83 tourist passengers

(b)  
3 pallets/65 tourist passengers

(c)  
4 pallet/34 tourist passengers

(d)  
5 pallet/29 tourist passengers

(e)  
6 pallets/11 tourist passengers

D.  This section of the Maintenance Manual describes the procedures necessary to convert the cabin accommodation from any one to any other of the available configurations. For information on how the cargo is secured within the cabin, how much may be loaded and how it should be distributed, refer to the Weight and Balance Control and Loading Manual.
2.  Passenger Accommodation
A.  The cabin is furnished for passenger accommodation. This includes floor coverings, passenger seats, partitions, overhead stowage compartments, passenger service units and windows.
B.  Seat spacing is different in each configuration.
5C8
Jun 20/85 25-09-100 Page 1
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.

3.  Cargo Accommodation (Passenger/Cargo Convertible Airplanes)
A.  When the whole cabin is converted for cargo accommodation, the passenger seats and floor coverings are removed. In this configuration, use is made of all seven floor tracks, three of which (one along the center of the floor and one along each outboard edge) are filled and covered in the passenger configuration.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 EQUIPMENT/FURNISHINGS(30)