S 434-126

 (2)  
Install the bleed air precooler to the nacelle strut structure.

 (a)  Install and tighten the fasteners to hold the upper aft side of the bleed air precooler to the nacelle strut structure.
 S 434-127
 (3)  
Position the exhaust flange of the bleed air precooler to the interface for bleed air duct at the nacelle strut firewall.

 S 434-128

 (4)  
Install the coupling to hold the precooler exhaust flange to the interface for the bleed air duct at the nacelle strut firewall.

 (a)  Tighten the coupling to 90-110 pound-inches.
 S 434-129
 (5)  Put the fixed leg of the forward support linkage in the lugs of the precooler.
 NOTE: Turn the eccentric bolt to adjust the forward support
____ linkage inboard/outboard as necessary to align it with the precooler.
 (a)  
Tighten the eccentric bolt when the parts are aligned.

 (b)  
Tighten the precooler lug.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-12-25
 ALL  ú ú 01 Page 411 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 434-130
 (6)  Install the fasteners to hold the adjustable leg of the forward support linkage to the precooler lugs.
 NOTE: The adjustable leg can be adjusted to align it in the
____
 precooler lugs.

 S 434-131
 (7)  If the adjustable leg of the forward support linkage needs to be adjusted, do these steps:
 (a)  
Adjust the length of the leg so that it aligns with the lug on the precooler.

 NOTE: The nominal length of the adjustable leg is 5.0 inches.

 (b)  
Make sure the rod end goes into the sleeve rod a sufficient distance so that a 0.04 inch diameter wire will not go through the inspection hole.

 (c)  
Safety the jamnut (AMM 20-10-44/401).

 S 434-132
 (8)  
Tighten the fasteners which hold the adjustable leg of the forward support linkage.

 S 434-133

 (9)  
Attach the lower support linkage to the precooler.

 (a)  
Apply anti-seize compound to the shank of the bolt.

 (b)  
Tighten the fastener.

 S 434-134
 (10) Connect the shortest support rod to the lower support linkage.
 (a)  
Keep the length of the support rod approximately 5.40 inches.

 (b)  
Install the fasteners.

 S 434-135
 (11) Connect the remaining support rod to the lower support linkage:
 (a)  
Adjust the length of the rod so that it freely aligns with the lower support link and the nacelle strut structure.

 (b)  
If the support rod has to be adjusted, make sure each rod end is in the support rod sleeve a sufficient distance so that a

 0.04 inch diameter wire will not go through the inspection hole.
 S 434-136
 (12) Tighten the fasteners to secure the support rods to the lower support link on the bottom of the precooler.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 36-12-25
 ALL  ú ú 02 Page 412 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 644-076
 (13)
 Apply a thin layer of the antiseize compound to the external threads of the sense line fitting and sense port.

 S 434-077

 (14)
 Connect the sense line to the pressure port on the precooler.

 S 434-078

 (15)
 Attach the wire bundle and the sense line to their respective clamp supports on the precooler.

 S 434-079

 (16)
 Install the pressure regulator and shutoff valve (PRSOV) (AMM 36-11-15/401).

 S 434-080

 (17)
 Install the precooler control valve (AMM 36-12-35/401).

 S 434-081

 (18)
 Install the outboard strut fire seal assembly door (Fig. 401).

　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 PNEUMATIC(94)