22-13-01
 ALL  ú ú 01 Page 603 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

3. BUSHING/BOLT 
5. CRANK/BOLT 
CONTROL  2. LEVER/BUSHING 
ROD 
4. BEARING/BOLT 
1. LEVER/BOLT  AUTOPILOT LATERAL 
SERVO 

B
LAS Mechanical Linkage Wear Limits Figure 601 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-13-01
 ALL  ú ú 01 Page 604 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Compare the dimensions you measured with the permitted dimensions shown in Fig. 601.

 (c)  
Repair or replace the parts that are out of the tolerance.

 S 426-003
 (3)  Install the parts.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-13-01
 ALL  ú ú 01 Page 605 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

NO. INDEX  PART NAME  DIM.  DESIGN LIMITS  WEAR LIMITS  PART WORN REPLACE  PART WORN REPAIR  INSTR REPAIR 
DIAMETER  PER-MITTED WEAR DIM.  ANCE CLEAR-MAX DIA 
MIN  MAX 
1  LEVER  ID  0.2495  0.2500  0.2505  0.0030  3 
BOLT  OD  0.2485  0.2495  0.2475  X 
2  LEVER  ID  0.4355  0.4366  0.4372  0.0027  3 
BUSHING  OD  0.4351  0.4361  0.4345  X 
3  BUSHING  ID  0.2495  0.2510  0.2520  0.0045  X 
BOLT  OD  0.2485  0.2495  0.2475  X 
4  BEARING  ID  0.2497  0.2500  0.2503  0.0028  1 
BOLT  OD  0.2485  0.2495  0.2475  X 
5  CRANK  ID  0.2495  0.2505  0.2515  0.0040  X  2 
BOLT  OD  0.2485  0.2495  0.2475  X 

REPLACE THE BEARING WHEN THE INTERNAL BEARING CLEARANCE IS LARGER THAN THE MAXIMUM VALUE OF 0.0004.
REFER TO OVERHAUL MANUAL FOR REPAIR INFORMATION.
REFER TO VENDOR MANUAL FOR REPAIR INFORMATION.

LAS Mechanical Linkage Wear Limits
Figure 601 (Sheet 3)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-13-01
 ALL  ú ú 01 Page 606 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 LATERAL AUTOPILOT SERVO ELECTROHYDRAULIC SERVOVALVE
___________________________________________________ AND SOLENOID VALVE - MAINTENANCE PRACTICES
__________________________________________
 1.  General_______
 A.  This procedure contains three tasks. The first is for the removal of the electrohydraulic servovalve (EHSV) or a solenoid valve from the Lateral Autopilot Servo (LAS). The second installs an EHSV or a solenoid valve on the LAS. The third task is a test of the LAS, and uses the Central Maintenance Computer System (CMCS).
 B.  You can find the LAS on the forward bulkhead of the left-hand wing landing gear well, adjacent to the Central Lateral Control Package -right autopilot (left hand CLCP). There is one EHSV and two solenoid valves, installed on the LAS.
 C.  The removal/installation procedures are the same for the EHSV and the solenoid valves.
 TASK 22-13-02-022-062
 2.  Lateral Autopilot Servo Electrohydraulic Servovalve and Solenoid Valve______________________________________________________________________ Removal (Fig. 201)_______
 A.  Special Tools and Equipment
 (1)  3MIT65B80190 - Wing Landing Gear Door Locks.
 B.  References
 (1)  
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AUTO FLIGHT(115)