曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 S 865-068
 (3)  Make sure the FLT CONTROL HYD POWER WING 1, 2, 3, and 4 switches are in the NORM position. These switches are on the Pilots' Overhead Maintenance Panel (P461).
 S 865-430
 (4)  Set the STAB TRIM 2 and 3 switches on Pilots' Control Stand to the AUTO position.
 S 865-432
 (5)  Use the manual trim switches (captain's or first officer's) on the Pilots' Control Wheel to set the stabilizer to 6 units of trim.
 S 745-434
 (6)  Do this check on the stabilizer surface position: (a) Push the LSK adjacent to <GROUND TEST from the CMC MENU page on the CDU.
 (b) (c) (d) (e)  Push the LSK adjacent to <22 AUTOPILOT FLT DIR from the GROUND TEST SYSTEMS page on the CDU.Push the LSK adjacent to <XDUCER OUTPUTS from the GROUND TESTS MENU page on the CDU.Continue with the instructions on the CDU to get the values for the stabilizer surface position.Write down the values for the stabilizer surface position:
 L ______ ,  C ______ ,  R ______ .

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-10-00
 ALL  ú ú 01 Page 565 ú Feb 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (f)  
Make sure that the values (left, center, and right channels) are between -2.7 and -3.3 degrees.

 (g)  
Make sure that the difference between channels (L-R, R-C, and L-C) is not more than 0.3 degree.

 S 745-436
 (7)  Do the stabilizer trim test:
 (a)  
Push the LSK adjacent to <GROUND TESTS from the CMC MENU page on the CDU.

 (b)  
Push the LSK adjacent to <22 AUTOPILOT FLT DIR from the GROUND TESTS page on the CDU.

 (c)  
Push the LSK adjacent to <STAB TRIM from the GROUND TESTS MENU page on the CDU.

 (d)  
Continue with the instructions on the CDU to get the stabilizer position for the FCC-L.

 (e)  
Write down the stabilizer position for the FCC-L:

 L ______ DEG.

 (f)  
Make sure that the stabilizer position for the FCC-L is between -10.2 and -10.9 degrees.

 (g)  
Push the LSK adjacent to <ADVANCE.

 (h)  
Push the captain's or first officer's autopilot disconnect switch two times.

 (i)  
Continue with the instructions on the CDU to get the stabilizer position for the FCC-R.

 (j)  
Write down the stabilizer position for the FCC-R:

 R ______ DEG.

 (k)  
Make sure that the stabilizer position for the FCC-R is between -10.2 and -10.9 degrees.

 (l)  
Push the LSK adjacent to <ADVANCE.

 (m)  
Push the captain's or first officer's autopilot disconnect switch two times.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-10-00
 ALL  ú ú 02 Page 566 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (n)  
Continue with the instructions shown on the CDU for a check of the FCC-C control of SRM-L and SRM-R.

 (o)  
Push the captain's or first officer's autopilot disconnect switch two times.

 (p)  
Make sure that the STAB TRIM test is completed with no failure.

 R. Rudder Autopilot Servo and Surface Limit Test
 S 865-140
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  
Make sure you supply hydraulic pressure to the hydraulic systems N0. 1, 2, 3, and 4 (Ref 29-11-00/201).

 S 865-139

 (2)  
Make sure the FLT CONTROL HYD POWER TAIL 1, 2, 3, and 4 switches are in the NORM position. These switches are on the Pilots' Overhead Maintenance Panel (P461).

 S 865-141

 (3)  
Make sure the FLT CONTROL HYD POWER WING 1, 2, 3, and 4 switches are in the NORM position. These switches are on the Pilots' Overhead Maintenance Panel (P461).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AUTO FLIGHT(64)