曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (3)  S 422-032To install a new lamp, put the lamp into the rear of the lens module. (a) Make sure the part number of the lamp is 387.
 (4)  S 432-021To install the lens module, do these steps: (a) Put the link pin into the rear of the groove on the bail plate and pull the link pin to the other end of the groove. (b) Push the lens module into the switch module.
 NOTE:____ Put the side that has the word "TOP" in the up position.
 (5)  S 862-023Supply the electrical power (Ref 24-22-00/201).
 (6)  S 862-024Remove the DO-NOT-CLOSE tags and close these circuit breakers: (a) P6 Main Power Distribution Panel 1) 6E21, FLT DK LIGHTS PANEL GLARESHIELD 2) 6F19, FLT DK LIGHT PILOT MISC IND 1 3) 6F20, FLT DK LIGHT PILOT MISC IND 2 4) 6L1, FLT DK LIGHT STBY INST (b) P7 Overhead Circuit Breaker Panel 1) 7D7, FLT CONT CMPTR SERVO L 2) 7D12, FLT CONT CMPTR SERVO C 3) 7D14, FLT CONT CMPTR SERVO R 4) 7E9, MCP L 5) 7E18, MCP R
 (7)  S 742-025Do this task:  Ground Test - Mode Control Panel (Ref 22-10-00/501).
 (8)  S 862-026Remove the electrical power if it is not necessary (Ref 24-22-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-02
 ALL  ú ú 01 Page 207 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 AUTOPILOT DISENGAGE SWITCH - REMOVAL/INSTALLATION
_________________________________________________
 1.  General_______
 A.  This procedure contains two tasks. The first task is for the removal of the autopilot disengage switch. The second task is for the installation of the autopilot disengage switch.
 B.  You can find the two autopilot disengage switches (S282 and S283) on each outboard horn of the pilots' control wheel. The switch is a single-action, multiple pole, pushbutton type. A switch plate holds the switch in position on the control wheel.
 TASK 22-11-03-004-027
 2.  Remove The Autopilot Disengage Switch (Fig. 401)_____________________________________
 A.  Special Tools and Equipment
 (1)  Insertion and Extraction Tool (Commercailly Available)
 B.  Standard Tools and Equipment
 (1)  Threading Wire - 30-inch length of standard wire (No. 18 to 22 gage), without insulation if possible.
 C.  References
 (1)  IPC 27-31-04, Fig. 3
 D.  Access
 (1)  Location Zones
 221 Control Cabin, LH
 222 Control Cabin, RH

 E.  Remove the Autopilot Disengage Switch
 S 864-028
 (1) Open these circuit breakers and attach the DO-NOT-CLOSE tags:
 (a)  P7 Overhead Circuit Breaker Panel
 1) 7D7, FLT CONT CMPTR SERVO L
 2) 7D8, FLT CONT COMPTR PWR L
 3) 7D12, FLT CONT CMPTR SERVO C
 4) 7D13, FLT CONT CMPTR PWR C
 5) 7D14, FLT CONT CMPTR SERVO R

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-03
 ALL  ú ú 01 Page 401 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

1.  SWITCH DISENGAGE AUTOPILOT 2.  PLATE SWITCH  3.  SCREW  4.  CONTROL COLUMN 
5.  CONTROL WHEEL 
6.  (4 SCREW-TYPE CONNECTIONS) TERMINAL BLOCK 
TERMINAL BLOCK INSULATOR 

STAB TRIM AND AUTOPILOT WIRE CONNECTIONS (JIFFY JUNCTION MODULES)  7.  APPROACH PLATE MEDALLION AND 
WIRE BUNDLE 

Autopilot Disengage Switch Removal/Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-03
 ALL  ú ú 01 Page 402 ú Feb 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 6) 7D15, FLT CONT CMPTR PWR R 7) 7E9, MCP L 8) 7E18, MCP R 9) 7E24, AUTO FLT WARN
 S 024-053
 (2)  Do the steps that follow to remove the autopilot disengage switch:
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AUTO FLIGHT(80)