76-11-11
 STANDS WITH A TIE ROD-AND-NUT THROUGH ú CONFIG 1 THE STABILIZER TRIM SHAFT ú C01 Page 402 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E64225
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
1. LEFT STABILIZER  TRIM CONTROL WHEEL
3. LEFT CONTROL  SHAFT NUT
2. AFT TIE STRAP
9. KEY
8. AFT COVER ANGLE
Control Stand Center Components Installation
Figure 402

4. FORWARD TIE STRAP
5.
 COVER ASSEMBLIES

6.
 FORWARD COVER ANGLE

7.
 STABILIZER TRIM CONTROL WHEEL SHAFT

 E64227
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH NON-REINFORCED CONTROL ú

 76-11-11
 STANDS WITH A TIE ROD-AND-NUT THROUGH ú CONFIG 1 THE STABILIZER TRIM SHAFT ú C01 Page 403 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
TASK 76-11-11-404-006-C01
 3.  Control Stand Covers, Seals and Lightplates Installation
________________________________________________________
 A.  References
 (1)  
AMM 26-21-51/401, Engine and APU Fire Control Module

 (2)  
AMM 29-15-00/201, Hydraulic System

 B.  Access
 (1)  Location Zones
 101 Control Cabin - Left
 102 Control Cabin - Right

 C.  Procedure
 S 424-007-C01
 (1) Do these steps to install the covers, seals and lightplates.
 (a)  
Install the cover assemblies (5, Fig. 401) on the control stand.

 (b)  
Install the horn cutout switch (16, Fig. 401).

 (c)  
Install the forward and aft cover angles (6 and 8, Fig. 402) on the control stand.

 (d)  
Install the forward and aft cover tie straps (4 and 2).

 (e)  
Install the fire control module (15, Fig. 401) for the engine and the APU in the aft electronics control panel (AMM 26-21-51/401).

 (f)  
Install the left and right upper side doors (6).

 (g)  
Install the right control wheel (7) on the spline shaft (2).

 NOTE: Handles on control wheels must be 90 (|15)
____ degrees apart when installed on the control stand.
 (h)  Install the tie rod (8) and attach with the tie rod nut (1) at each end.
 NOTE: It is recommended that you discard the old tie rod
____ nuts and replace with new tie rod nuts.
 1)  Tighten the tie rod nuts to 60-70 inch-pounds (6.8-7.9 newton-meters).
 NOTE: Make sure at least two threads on the tie rod
____ show after you tighten the tie rod nut.
 S 864-008-C01
 (2) Supply hydraulic power if it is necessary (AMM 29-15-00/201)
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH NON-REINFORCED CONTROL ú
 76-11-11 STANDS WITH A TIE ROD-AND-NUT THROUGH ú CONFIG 1 THE STABILIZER TRIM SHAFT ú C01 Page 404
 ú  Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
CONTROL STAND COVERS, SEALS AND LIGHTPLATES - REMOVAL/INSTALLATION
__________________________________________________________________
 TASK 76-11-11-904-001-C02
 1. Control Stand Covers, Seals and Lightplates Removal and Installation
____________________________________________________________________
 A. General
 (1) Do not use this configuration.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS REINFORCED CONTROL ú
 76-11-11 STANDS WITH A TIE ROD THROUGH THE SPLINE ú CONFIG 2 SHAFT ú C01A Page 401
 ú Mar 15/96
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 發動機控制 ENGINE CONTROLS(85)