28-44-01
 ALL  ú ú 01 Page 404 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

NOTE:  STICK INSTALLATION IS THE SAME FOR ALL HOUSING TYPES.
Fuel Measuring Stick Figure 402
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-44-01
 ALL  ú ú 02 Page 405 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (2)  
Access Panel
 191GL Fuel Drain and Dripstick Access Door

 D.
Procedure

 S 424-008
 (1)  
Put the measuring stick (1), with the head (8) removed, into the housing.

 S 434-009

 (2)  
Install the guide (2), spring (3), and retainer (4) in the housing and hold in position.

 S 434-025

 (3)  
Install a new gasket (5) and seal (7) in the socket (6).

 S 434-011

 (4)  
With the installation tool, turn the socket (6) in the mounting base until the socket (6) aligns with the tank lower surface or access door.

 S 864-027

 (5)  
Lower the measuring stick (1).

 S 434-019

 (6)  
Install the head (8) on the measuring stick (1).

 S 864-020

 (7)  
Lift the measuring stick (1) to its initial position.

 S 434-021

 (8)  
Push and turn the head (8) clockwise in the socket (6) to lock the measuring stick (1).

 S 414-013

 (9)  
For the measuring stick in the center wing tank, close the fuel drain and dripstick access door, 191G.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-44-01
 ALL  ú ú 03 Page 406 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 FUEL MEASURING STICK HOUSING - REMOVAL/INSTALLATION
___________________________________________________
 1.  General_______
 A.  This procedure contains tasks to remove and install the housing of the fuel measuring stick.
 (1)  
There are different tasks to remove and install a housing on an access door or a housing in the lower wing.

 B.  
To make the identification of the housings easier, the housings numbers agree with the measuring stick numbers.

 C.  
The mounting base holds the housing at the bottom.

 (1)  
For housings No. 17 and 24, the mounting based is canted.

 (2)  
For housings No. 17, 19, 20, 24, the top ends of the housing are held by clamps attached to the upper wing structure.

 (3)  
Housing No. 22 does not have a top support bracket.

 (4)  
Housings No. 18, 21, 23, 33 and 34 are installed in access doors and are removed with the access doors.

 (5)  
Housing No. 18 has a guide at the top end of the housing.

 TASK 28-44-02-004-001
 2.  Fuel Measuring Stick Housing No. 18, 21, 23, 33, or 34 Removal (Fig. 401)______________________________________________________________
 A.  Equipment
 (1)  
Wrench - Hex, 9/16 inch, local purchase

 B.  
References

 (1)  
AMM 28-11-00/201, Fuel Tanks

 (2)  
AMM 28-11-02/401, Reserve and Main Tank Access Door

 (3)  
AMM 28-26-00/201, Defueling

 (4)  
AMM 28-44-01/401, Fuel Measuring Stick

 (5)  
AIPC 28-41-01 Fig. 1

 C.  
Access

 (1)  
Location Zones 545 Inbd Main Tank (Part), Mid Spar to Rear Spar, Left 546 Outbd Main Tank (Part), Mid Spar to Rear Spar, Left 553 Reserve Tank, Front Spar to Rear Spar, Left 645 Inbd Main Tank (Part), Mid Spar to Rear Spar, Right 646 Outbd Main Tank (Part), Mid Spar to Rear Spar, Right 653 Reserve Tank, Front Spar to Rear Spar, Right

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 4(159)