(1)
AMM 24-22-00/201, Manual Control
(2)
AIPC 28-31-05 Fig. 2
(3)
SSM 28-31-03
(4)
WDM 28-31-13
C.
Access
(1)
Location Zones
556 Dry Bay, Front Spar to Rear Spar, Left
656 Dry Bay, Front Spar to Rear Spar, Right
(2)
Access Panels
556AB Wingtip Dry Bay Access Door
656AB Wingtip Dry Bay Access Door
D.
Install the Actuator
S 114-054
(1)
Prepare these surfaces for an electrical surface bond (SWPM 20-20-00):
(a)
Faying surface of the index plate and valve actuator.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-31-05
ALL ú ú 01 Page 405 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b) Faying surface of the bonding jumper and bonding jumper tab.
S 864-010
(2)
Make sure that the manual override lever is in the CLOSED position.
S 424-011
(3)
Put the actuator into the correct position on the rear spar.
S 434-037
(4)
Engage the actuator shaft that has splines to the valve body.
S 434-012
(5)
Install the screws and washers (4 locations) to
attach the actuator to the valve body.
S 414-038
(6)
Attach lockwire to the screws.
S 434-013
(7)
Install the bonding jumper on the actuator (SWPM 20-20-00).
S 764-055
(8)
Measure the electrical resistance between the actuator (1) and the spar (SWPM 20-20-00).
NOTE: The resistance must not be more than 0.008 ohm.
____
S 434-014
(9) Attach the electrical connector, DV56, to the actuator, V56 (left wing), or the electrical connector, DV49, to the actuator, V49 (right wing).
TASK 28-31-05-714-040
4. Jettison Nozzle Valve Operational Test______________________________________
A. References
(1)
AMM 12-11-01/301, Fuel Tank - Servicing
(2)
AMM 24-22-00/201, Manual Control
(3)
AMM 27-81-00/201, Leading Flap System
(4)
AIPC 28-31-05 Fig. 2
(5)
SSM 28-31-03
(6)
WDM 28-31-13
B.
Access
(1)
Location Zones
556 Dry Bay, Front Spar to Rear Spar, Left
656 Dry Bay, Front Spar to Rear Spar, Right
(2)
Access Panels
556AB Wingtip Dry Bay Access Door
656AB Wingtip Dry Bay Access Door
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-31-05
ALL ú ú 01 Page 406 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
C. Do a Test for the Operation of the Jettison Nozzle Valve
S 864-016
(1)
Supply the electrical power, if it is not available
(AMM 24-22-00/201).
S 864-034
(2)
Make sure these circuit breakers are in the closed position:
(a)
On the DC power distribution panel P180:
1) 180M8, FUELING VALVE 2
2) 180M9, FUELING PWR - HOT BAT
3) 180C25, FUELING LTS PANEL
4) 180C26, FUELING LTS RECP
(b)
On the left power distribution center, P414: 1) 414F17, FUELING VALVE 2) 414F22, FUELING PWR
S 864-035
(3)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
On the main power distribution panel, P6:
1) 6C18, JTSN NOZZLE VLV CONT R
2) 6D18, JTSN NOZZLE VLV CONT L
S 864-027
CAUTION: MAKE SURE THESE CIRCUIT BREAKERS ARE OPEN AND YOU ATTACH
_______ DO-NOT-CLOSE TAGS. IF YOU DO NOT OPEN THE CIRCUIT BREAKERS, YOU CAN CAUSE THE FUEL TO FLOW TO THE GROUND.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 4(51)
