spar must be at or below .001 ohm.
(m)
Connect the bond jumper (AMM 20-11-15/401).
(n)
Make sure the resistance between the heat exchanger tube and lower wing structure is satisfactory (AMM 20-22-01/601): 1) The resistance between the heat exchanger tube and the
structure must be at or below .005 ohm
(o)
Install a lockwire on the nuts.
(p)
Apply the fillet seal BMS5-26 to both sides of the rear spar. (Fig. 401)
(q)
Apply BMS10-20 to all cleaned areas still exposed after application of fillet seal.
(r)
Install the adapter fittings on the inlet and outlet fittings.
(s)
Remove the caps from the hydraulic tubes.
(t)
Connect the hydraulic tubes to the adapter fittings. 1) Tighten the B-nuts to 450-550 pound-inches (50-60 N.m).
S 414-047
CAUTION: REMOVE ANY CONTAMINATION OF REMAINING ABRASIVE, FINISH AND
_______ METAL SURFACE MATERIAL FROM THE FUEL TANKS. CONTAMINATION CAN CAUSE DAMAGE TO EQUIPMENT.
(2)
Install the access door for the primary fuel tank (AMM 28-11-02/401).
(3)
Do this task: "Hydraulic Reservoir Servicing" (AMM 12-12-01/301).
S 614-026
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-11-22
ALL ú ú 02 Page 406 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(4) S 864-045Pressurize the reservoir in the applicable hydraulic system (AMM 29-11-00/201).
(5) S 864-039Pressurize the applicable hydraulic system with a demand pump (AMM 29-11-00/201).
(6) S 864-038Remove the hydraulic power (AMM 29-11-00/201).
(7) S 014-040Remove the access door for the applicable fuel tank (AMM 28-11-02/401).
(8) S 864-041Prepare the applicable fuel tank for entry (AMM 28-11-00/201).
(9) S 794-042Examine the heat exchanger, the heat exchanger fittings, and the hydraulic tubes for leakage.
S 794-043
(10)
Also examine the hydraulic line connections at the heat exchanger fittings, on the aft side of the rear spar, for leakage.
(a)
If you find leakage, repair the cause of it.
S 414-044
(11)
Install the access door for the applicable fuel tank (AMM 28-11-02/401).
S 654-037
(12)
Fill the applicable fuel tank (AMM 12-11-01/301).
S 794-027
(13)
Examine the inlet and outlet fittings for the heat exchanger, on the aft side of the rear spar, for fuel leakage.
(a)
If you find leakage, repair the cause of it.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-11-22
ALL ú ú 01 Page 407 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 414-030
(14)
On systems No. 1 or 4, close the hydraulic access panel (AMM 06-09-08/201).
S 864-032
(15)
Remove the electrical power if it is not necessary (AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-11-22
ALL ú ú 01 Page 408 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
HEAT EXCHANGER - INSPECTION / CHECK
___________________________________
1. General
_______
A. This procedure contains a hydraulic leakage check of the heat exchangers as an alternative to analyzing fuel samples. A dry air pressure source is used for pressurizing the system. It will be necessary to gain access to the tube connections of the heat exchangers. On systems 1 and 4, get access to the tube connections through the access panel forward of the inboard aileron. On systems 2 and 3, get access to the tube connections through the applicable wheel well for the wing landing gear.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 液壓 HYDRAULIC 2(39)
