S 434-024
(3)
Attach the clamp to the bracket with a bolt, the two washers, and a nut.
S 424-013
(4)
Put the bracket and the position switch on the shutoff valve actuator.
S 434-025
(5)
Install the two bolts and washers to attach the bracket to the shutoff valve actuator.
S 434-014
(6)
Attach the electrical receptacle to the shutoff valve actuator with the four bolts, eight washers and four nuts.
NOTE: The washers must be against the bolt heads and the nuts.
____
S 764-015
(7) Make sure there is electrical continuity between pins 2 and 3 of the electrical receptacle.
NOTE: The shutoff valve must be in the closed position and the
____ shaft of the shutoff valve actuator must be in the fully retracted position.
S 824-016
(8) Turn the locknuts until the plunger of the position switch touches the lever and causes an open circuit between pins 2 and 3.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-11-39
ALL ú ú 01 Page 404 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 824-026
(9)
Turn the locknuts to move the position switch 0.03-0.04 inch (0.76-1.02 mm) more in the direction of the lever.
S 434-027
(10)
Tighten the locknuts.
S 434-028
(11)
Safety the locknuts with a lockwire.
S 434-017
(12)
Connect the applicable electrical connector to the shutoff valve actuator:
(a)
DM647B for system 1
(b)
DM874B for system 4
S 864-029
(13)
For the applicable hydraulic system, remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P7 Overhead Circuit Breaker Panel
1) 7F03 HYDRAULICS HYDIM 1
2) 7G03 HYDRAULICS HYDIM 2
3) 7H03 HYDRAULICS HYDIM 3
4) 7J03 HYDRAULICS HYDIM 4
S 414-018
CAUTION: MAKE SURE YOU LATCH THE DOORS ON THE TRAILING EDGE FAIRING
_______ CORRECTLY. IF THE DOORS OPEN DURING A FLIGHT, THIS CAN CAUSE DAMAGE TO THE DOORS.
(14) Close the left door of the trailing edge fairing (AMM 54-62-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
29-11-39
ALL ú ú 01 Page 405 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
HYDRAULIC CONTROL MODULE - REMOVAL/INSTALLATION
_______________________________________________
1. General_______
A. This procedure has two tasks. The first task removes the hydraulic control module. The second task installs the hydraulic control module.
B. The hydraulic control module is on the overhead panel, P5.
TASK 29-11-40-004-001
2. Hydraulic Control Module Removal (Fig. 401)________________________________
A. Access
(1)
Location Zone
200 Flight Compartment
B.
Procedure
S 864-002
(1)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P6 Main Power Distribution Panel 1) 6F19 FLT DK LIGHTS PILOT MISC IND 1 2) 6F20 FLT DK LIGHTS PILOT MISC IND 2 3) 6F26 FLT DK LIGHTS F/O IND 4) 6F27 FLT DK LIGHTS F/O IND & DGTL DSPL 5) 6L4 FLT DK LT CAPT IND 6) 6L5 FLT DECK LIGHT CAPT IND DGTL DSPL
(b)
P7 Overhead Circuit Breaker Panel
1) 7F1 HYDRAULICS DEMAND 4
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 液壓 HYDRAULIC 2(65)
