(2)
284U4049-49 - Shim, 0.003-inch thick (quantity - AR)
E. References
(1)
AMM 07-11-01/201, Jack Airplane
(2)
AMM 24-22-00/201, Manual Control
(3)
IPC 31-41-04, Fig. 1
F. Access
(1) Location Zones
735/736 Wing Landing Gear
755/756 Body Landing Gear
G. Shim Installation
NOTE: Load sensors shall not be installed at this time.
____
S 584-191
(1) Lift the airplane on jacks to remove all weight from the main landing gear (AMM 07-11-01/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-41-05
ALL ú ú 16 Page 411 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
(2) S 154-200Use the paint stripper, TURCO 5351, to remove paint from the surface of each mounting lug that touches the load sensor.
(3) S 104-201Use solvent, BMS 11-7 to clean the surface of the mounting lug.
(4) S 424-192Install the load sensors. Installation procedure. Use the Main Landing Gear Load Sensor
NOTE:____ Do not do the zero adjustment on jacks (mode 99).
(5) S 704-193Do these steps to use mode 22 of the WBC to read the digital voltage count of each load sensor: (a) Open the keyboard cover on the front of the WBC. (b) Push the MODE key. (c) Use the keyboard to put in 22__ (d) Push the ENTER key. (e) When OK shows, push the ENTER key. (f) Push the + or - key until the identification number of the desired load sensor is displayed. (g) Record the digital voltage count of the selected load sensor. (h) Repeat the above steps for each remaining load sensor.
(6) S 704-194The recorded mode 22 digital voltage count for each selected load sensor shall be 26467 to 37717.
(7) S 424-196Do these steps to select shims to get the specified mode 22 count: (a) Remove the load sensor. Use the Main Landing Gear Load Sensor Removal procedure.
NOTE:____ Put the shim on the lug adjacent to the electrical plug on the load sensor to increase the digital voltage count; put the shim on the opposite lug to decrease the digital voltage count.
(b) (c) Use a 0.002-inch thick shim (284U4049-55) to change the voltage count by approximately 9000.Use a 0.003-inch thick shim (284U4049-49) to change the digital voltage count by approximately 13,500.
NOTE:____ Use no more than two shims for each pair of mounting lugs.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-41-05
ALL ú ú 11 Page 412 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(d) Apply adhesive, BMS 5-26, only to the shim tab surface that touches the mounting lug. If you use two shims, apply adhesive to tab surfaces that touch.
NOTE: Do not allow adhesive to get on main surface between
____ shim and mounting lug on load sensor.
(e)
Install the shim with the tab set away from the mounting lug.
(f)
Bend the tab in the shim until it touches the mounting lug.
S 424-197
(8) Install the load sensor. Use the Main Landing Gear Load Sensor Installation procedure.
NOTE: Do not perform zero adjustment on jacks (mode 99).
____
S 704-198
(9)
Use mode 22 of the WBC to read the voltage count of each load sensor. The digital voltage count shall be 26467 to 37717. If not, repeat shim selection procedure.
S 824-199
(10)
Do the Zero Adjustment on Jacks (Mode 99) in the Main Landing Gear Load Sensor Installation.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-41-05
ALL ú ú 08 Page 413 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 指示/記錄系統 1(126)
